翘曲

Standard of ornamental design acceptance of work: Ornamental design project is finishing dry hind, just can check and accept; Check and accept ornamental design project, whether does the breed that should check ornamental design, norms, design accord with design requirement; Ornamental design should be installed firm, its quality asks to reach tolerance, should accord with: The level of form ornamental design and perpendicular tolerance, every meters must not be more than 5 millimeter, must not be more than 3 millimeter endlong; The tolerance of position of alone ornamental design, must not be more than 10 millimeter; Ying Guangjie of ornamental design surface, design clarity, juncture rigor, must not interstitial, warp, edge damage drops the blemish such as horn; Back up spends exterior Ying Guangjie, design clarity, without break.

花饰工程验收标准：花饰工程完工并干燥后，方可验收；验收花饰工程，应检查花饰的品种、规格、图案是否符合设计要求；花饰应安装牢固，其质量要求及允许偏差，应符合：条形花饰的水平和垂直允许偏差，每米不得大于5毫米，全长不得大于3毫米；单独花饰位置的允许偏差，不得大于10毫米；花饰表面应光洁，图案清晰，接缝严密，不得有裂缝、翘曲、缺棱掉角等缺陷；裱花表面应光洁，图案清晰、无裂缝。

Mallotus japonicus wood :Well luster, coarseness fabric, dryness slowly, hard to warping, esay to machining, esay for nailholding.

楸木：木材有光泽，结构略粗，干燥速度慢，不易翘曲，易加工，钉着力强。

Based on the fundamental assumptions of thin-walled structure,bendingand torsion of monosymmetric I-section thin-walled curved beams with smalldeformation were studied in detail.

从薄壁构件的基本假设出发，对薄壁曲梁小变形时的弯曲与扭转进行了详尽的分析，首次得出了单轴对称工形截面曲梁的翘曲位移、正应力、剪应力、应力合力以及适用于各种荷载作用的控制方程的精确表达。

Bending and torsion of monosymmetric I-section thin-walled curvedbeams with large displacement were studied in detail.The accurate expressions ofwarping displacement,normal stress,shear stress were given as well asgeneralized stress-strain relation.

对薄壁曲梁的有限位移理论进行了详尽的分析，得出了有限位移理论中单轴对称工形截面曲梁的翘曲位移、正应力、剪应力以及广义应力—应变关系的的精确表达。

Blade of the blade-like rotafiong planeness skinpass and warping largely depends on the installation method, of course, it is also possible to operate the blade with turret or tablets, Tablet press there was something in the stick.

刮刀的水平度平整度刮刀的平整与翘曲主要取决于安装的方法，当然也有可能与刀架槽或刮刀片、压片上粘有异物有关。

Findings in this study also indicate that warpage is inversely proportional with mold temperature, melt temperature, packing pressure and packing pressure time but directly pro- portional with cooling time at least for the problem of interest.

这研究的调查结果也指出翘曲对模子温度、融化温度感到反的比例，包装压力而且包装压力除了 directl 之外计时职业者- portional 用冷却的时间至少为重要问题。

The principle of precompensation for deformation was presented,which was applied to the shaping of an automobile fan and effectively helped lower the shrinkage deformation and warpage of the product.

介绍了变形预补偿的原理，以汽车风扇为例，成功地降低了汽车风扇的收缩变形和翘曲变形，为解决制品变形问题提供了一条新的思路。

The flow properties of linear low density and low density polyethylene blend under the extrusion conditions were investigated with capillary rheometry .

LLDPE为新一代聚乙烯，其制品在存放及使用过程中显示出一些突出的特点，如优异的机械强度、耐环境应力开裂性、耐热性、耐寒睦和抗翘曲性等。

Based on the trigonometrical theory, the out-plane displacement can be obtained by measuring the in-plane displacement, and then the elasticity thermal stress of the chip is evaluated when the application of the temperature field is repeated.

根据三角法测量技术原理，将离面位移的测量转化为面内位移的测量，从而获得了芯片受热后的翘曲形变和弹性应变分布。

Q: How can I avoid warping?

问：我如何避免翘曲？

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。