缺陷

Yellow or light eyes are to be strongly penalized, along with a walleyed or staring expression.

黄色眼睛或浅色眼睛属于严重缺陷，连带着，斜眼或表情刺眼也属于缺陷。

6 If, during the warranty period specified in Clause 14 and as a result of inspection by the Administration or otherwise, it is found that the quality or specifications of the Goods are not in conformity with the Contract or if the Goods are proven to be defective for any reason, including latent defects or the use of unsuitable materials, the Buyer shall promptly notify the Seller of the existence of a claim.

如果在合同条款第14条规定的保证期内，根据检验检疫局的检验结果，发现货物的质量或规格与合同要求不符，或货物被证实有缺陷，包括潜在的缺陷或使用不合适的材料，买方应及时向卖方提出索赔。

7 If, during the warranty period specified in GCC Clause 18 and as a result of inspection by the Administration or other organization, otherwise, it is found that the quality or specifications of the Goods are not in conformity with the Contract or if the Goods are proven to be defective for any reason, including latent defects or the use of unsuitable materials, the Purchaser shall promptly notify the Supplier of the existence of a claim.

8.7 如果在合同条款第18条规定的保证期内，根据检验检疫局或其他机构的检验结果，发现货物的质量或规格与合同要求不符，或货物被证实有缺陷，包括潜在的缺陷或使用不合适的材料，买方应及时向卖方提出索赔。

3 Should the quality and specifications of the goods be not in conformity with contract, or should the goods prove defective within the warranty period stipulated in Clause 14 for any reason, including latent defect or the use of unsuitable materials, the Buyer shall arrange for a survey to be carried out by the Administration, and have the right to claim against the Seller on the strength of the CIQ.

15.3 如果货物的质量和规格不符合合同，或货物在条款第14条规定的保修期内，不管任何原因证明有缺陷，包括潜在的缺陷或使用不合适的材料，买方应安排行政机构进行调查，并有权由出入境检验检疫局向卖方索赔。

It is known from the experimental outcome that the sound frequency in attached area with defect is high and with completeness is low; the intensity in attached area with defect is weak and with completeness is strong.

经实验结果可得知瓷砖黏贴缺陷处之声音频率较高，而黏贴完整处之声音频率较低；瓷砖黏贴缺陷处之黏著强度较小，而黏贴完整处之黏著强度较大。

Faults--A soft outer coat is a very serious fault as is a wooly textured outer coat.

缺陷：柔软的外层披毛与羊毛质地的外层披毛是非常严重的缺陷。

The paper analyses the workpiece defect and advances a new method,which is applied to eliminate defect.

本文分析了该模锻件产生缺陷的原因和消除缺陷的方法。

Experimental results indicate that the growth of bacteria is retarted seriously in the media containing ethyl xanthate more than

对矿石抛光面实验的结果表明，细菌对黄铁矿的浸蚀作用在晶格缺陷处和解理面方向均可进行；而对毒砂的浸蚀作用则只在缺陷较为明显处选择性进行，显示出细菌对黄铁矿的直接作用更为明显。

The study of vertical channel with high field effect mobility by Ni induced lateral crystallization, which can form larger grains on channel regions and reduce grain boundary defects. We detect the method of Ni induced lateral crystallization through high field effective mobility, but that accumulates too much Ni on floating N+ region and causes defects and metal contamination. As Ni is used to form silicde and then proceed to low temperature annealing, we can observe the floating region that has no Ni acumination regions or contaminations. This aids us in obtaining good electronic performance of this device, not only the remote field effective mobility but also the vast improvement of sub-threshold swing and on/off currents.

接著，是延续垂直通道的研究，希望能有效的提升电子迁移率，因此以镍金属诱导横向结晶的方式使通道形成较大的结晶，减少矽晶粒之间的缺陷，而在初步的研究，发现以镍金属直接诱导横向结晶的方式，经由低温长时间回火之后，由於镍金属扩散的关系，完成诱导结晶之后，有过多的镍金属聚集在顶部参杂的中间区域，而造成过多的缺陷累积，虽然电子迁移率有效的提升，但整体的电性并不如预期，因此提出先形成镍金属矽化物后，将未反应的镍金属或金属氧化物去除之后，再进行镍金属矽化物诱导横向结晶处理，经由结果观察得知在顶部掺杂区域部分没有明显的镍金属累积或污染，并且得到很好的整体电性，除了电子迁移率有效提升之外，次临界特性以及导通电流都能有效改善。

It is found that adatom yields, vacancy yields and sputtering yields will all increase along with the energy of incident atoms getting higher. Meanwhile, the quantities as well as distribution of adatom and vacancy play an important role in film growth.

表面吸附原子、空位缺陷以及溅射产额均随入射原子能量的增加而增加；表面吸附原子与空位缺陷的数量与分布，对于薄膜生长模式起着重要作用。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。