绝热的

In spite of the limited air sounding data, we would use the adiabatic lapse rate method and the time interpolation to get the hourly mixing height.

所以采用乾绝热递减方法在局部地区的混合层模拟上，仍然容易受到如探空资料及地面温度的影响而产生误差。

Consequently adopt the adiabatic lapse rate method to simulate the local MH may occur the inaccuracy by air sounding data and local surface temperature.

所以采用乾绝热递减方法在局部地区的混合层模拟上，仍然容易受到如探空资料及地面温度的影响而产生误差。

For the boundary layer with adiabatic wall, transition happens about 60% further downstream from the nose of the cone, as compared with boundary layer with isothermal wall.2 ZARF is not unique in three-dimensional boundary layer.

壁面温度边界条件对转捩影响很大，绝热边界层和等温边界层相比，转捩位置靠后将近60%。2三维边界层中的ZARF曲线不是唯一的。

We present the unique correspondence between R〓 and the outer boundary R〓 of ADAF-thin disk solutions.

我们发现存在三种类型的整体解：ADAF-标准薄盘解、ADAF-厚盘解和含α-X型绝热激波的解。

The mechanisms of double photoionization of these molecules are discussed based on comparison of our experimental results with those predicted theoretically.

总的来说我们实验测得的双电离能与理论计算获得的绝热双电离能比较吻合。

In addition, the life-time of Kapton films and the equilibrium temperature of the adiabatic plane of the second surface mirror were predicted.

最后对Kapton薄膜的存在寿命和Kapton/Al薄膜二次表面镜绝热平面的平衡温度进行了预测。

In order to obtain the process design data of platforming plant, the pilot plant studies have been made in a multiple adiabatic reactor system containing three or four reactors in series.

为了提供铂重整工业装置的设计数据及操作指标，进行了三个和四个串联绝热反应器的中型试验。

The liner is a polymeric elastomer coating between propellant and insulation layer or case.The liner-forming is a special step in production of solid rocket motor.

衬层是推进剂与绝热层或壳体之间的高分子弹性体涂层，衬层成型是固体火箭发动机生产中的一种特种工序。

In ordcr to solve the problem of expcnsive aluminium type thermite currently used for ingot casting at Pangang's Steelmaking Plant,a new and cheap substitutional thermal insulation a-gent is developed.

针对攀钢炼钢厂模铸铝型发热剂价格高的问题，研制了一种新型价廉的绝热保温覆盖剂取代铝型发热剂。

The unimproved testing device and method is based on the manual work, the error is inevitable.

评价一种磁性制冷材料的性能好坏，对其进行绝热温变测试是很重要的一步。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。