结果为

Based on the load transmission mechanism of space truss, and referenced theanalysis of test materials, a formula for calculating the bearing capacity of reinforcedconcrete compression strut is introduced. By using the theory of plastic hinge-line, anupper limit solution of bent bearing capacity for four-pile cap, which coincidesprecisely with the practical measurements, is obtained. By utilizing the reaction ofthe soil under cap and by basing on the method of plastic ultimate analysis, an upperlimit solution of punching shear bearing capacity for pile cap is acquired, which. coincides precisely with the practical measurements, and the formula is similar to thecode.A brief discuss on cooperative work of strip beam of foundation and single rankof piles is made. Separately considering the pile-cap and the pile-group, thencoupling their matrix of rigidity, the inner force of pile-cap is solved by the numericalmethod under some reasonable supposition. In comparison with other method, thecalculating results are exact, reliable and convenient in using. The method provides apowerful tQol fOr further analysis and research on this kind of structure.

本文以空间桁架传力机理为基础，结合试验资料分析，推导了钢筋混凝土等边三桩承台受冲切承载力计算公式；根据塑性铰线理论，导得了与试验结果吻合良好的四桩承台受弯承载力的上限解；利用承台底土反力分布，根据塑性极限分析方法，导得了桩基承台受冲切承载力的上限解，在此基础上，通过简化假定，得到与规范公式相类似的承台受冲切承载力实用公式，该公式能方便考虑台底土反力作用，与试验结果的吻合程度比规范公式好；简要讨论了桩基条形承台梁与单排桩的协同工作分析；在一些合理假定的基础上，将承台与群桩分开考虑，分别得到其刚度矩阵后进行耦合，通过数值方法求解承台内力，算例表明，该方法结果准确，使用方便，为该类结构的进一步分析研究及工程设计提供了强有力的工具。

The regulation of gene expression is to have relations to the assembly of the DNA binding proteins which bind to DNA to initiate the transcription. Some of these proteins have the ability to promote bending or looping of DNA. The FIS protein regulates gene expression in Escherichia coli by this property of bending DNA. There are many researches to discover the mechanism of FIS protein binds to DNA. However the experiment data only show the supposititious results and figure out the model of FIS-DNA complex structure. This research uses molecular dynamics simulation to compute the detail of the interaction between FIS and DNA. We observed FIS prominently affects the DNA bending by the type of local bending. Analyzing the DNA structure properties, roll and slide, also demonstrates the local bending type and region. The hydrogen bonds between FIS and DNA are analyzed to compare with the experiment data. Finally we compute the binding free energy between FIS and DNA to estimate the result of simulation and compare with the value of λ-repressor-DNA complex.

基因的表现与结合於DNA促使DNA转录作用起始的DNA结合蛋白组装有关，一些这类的蛋白质具有促使DNA扭曲或将DNA形成环状的能力，FIS蛋白质即是藉由扭曲DNA的特性调控大肠杆菌基因的表现，目前已有很多的研究发现FIS与DNA结合的机转，然而这些实验的数据仅能显示推测性的结果，进而利用这些结果推论出FIS与DNA聚合体结构的模型，本研究利用分子动态模拟的方式计算FIS与DNA交互作用的细节，我们观察到FIS主要影响DNA的扭曲方式为DNA区域扭曲的类型，并且分析DNA结构特性roll与slide也指出扭曲方式为区域扭曲与其扭曲的区域，我们也分析FIS与DNA之间的氢键，并且与实验的资料作比较，最后我们计算FIS与DNA之间的结合自由能评估模拟的结果，并且计算出的值和λ-repressor与DNA聚合体结构的实验值作比较。

In 8 cases, both the results were consistent excepting for minor discrepancies.③In 3 cases, including 2 each with triploidy and tetraploidy respectively, and one with chimeric karyotype of normal/+22, the results from the two methods were discrepant.

CGH与常规R带的分析结果比较可分为三种：①CGH和常规核型分析结果完全一致的有3例；②CGH分析和R带分析从不同角度提供了相对一致信息的有8例；③CGH分析和R带分析结果不一致的有3例，其中2例分别为约三倍体和约四倍体，另1例为正常/＋22嵌合型。

Meanwhile, the coated surface was hydrophobic with a contact angle of 107.2°since the introduction of methyl groups and methylene groups. Static immersing corrosion test, potentiodynamically polarization curve and electrochemical impedance spectroscopy were conducted to evaluate the film corrosion performances. The results of potentiodynamically polarization curve and EIS in 55wt% LiBr solutions at room temperature in atmospherical pressure indicated that the corrosion current density of BMBSE film coated surface was 4 orders of magnitude smaller than that of bare SUS304 steel, and the impedance was increased by a factor of 10000. Static immersing corrosion test presented that the BMBSE film can significantly increase the corrosion resistance in 55wt%LiBr solution at 180°C compared with stainless steels.

同时由于有机组分甲基和亚甲基的引入，结构均匀致密，并具有一定的疏水性；电化学测试结果表明BMBSE膜的极化阻抗比不锈钢大4个数量级，自腐蚀电流密度也下降低了4个数量级左右，具有良好的耐腐蚀性能；成膜的影响因素优化结果表明BMBSE、EtOH、D.I.water摩尔比为1∶4∶3，热处理温度为200℃时，更有利于制备结构均匀、致密、耐腐蚀性能好的薄膜；静态浸泡腐蚀实验结果说明，在180℃、55%的高温溴化锂溶液中BMBSE膜能起到良好的腐蚀防护作用。

Four methods for evaluating circularity error. least-squares method for evaluating cylindricity error. 3.Using language of VC++, a software of form error evaluating is developed. Module structure is adopt in this software and every element has one module.

用VC++开发了形状误差的评定软件，软件采用功能模块结构，每种元素均设计为一个独立的模块，为使评定结果更加直观，采用OpenGL对处理的结果进行了可视化处理，结果图形可以随意转动和缩放，以方便观察。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

The results show that the Yager's ranking method is better than the centroid method when the fuzzy numbers of the input factors are dissymmetric. So the solving procedure of the Yager's ranking method is more suitable for this kind of problem.

结果显示，当要素价格为非对称的模糊数值时，Yager 排序法所得到的结果会优於重心法所求解之结果；故Yager 排序法的求解程序为此类问题的较佳求解方法。

The results show that the introducing of multivinyl monomer and CaCO3 can slow down polymerization rate to different extent.Using 1％～5％ trimethylolpropane trimetbacrylateor divinyl benzene,tight encapsulation of CaCO3 can be realized and beyond 94％PS cannot be extracted. The amount of crosslinker or emulsifier should be accommodated when the load amount of CaCO3 is increased.CaCO3 content in the product increases consequently with the increase of the loaded amount of CaCO3,which can be known from FT-IR and TGA.TEM observations reveal that when the load amount of CaCO3 is 14.8％,most CaCO3 particles are encapsulated and each latex particle contains one CaCO3 particle.Composite particles have well-defined core—shell structure and the thickness of polymer shells is around 10 nm.However,the thickness of polymer shell decreases and many free CaCO3 particles appear when the load amount of CaCO3 reaches 29.3％and 58.7％,respectively.

结果表明，多乙烯基单体以及碳酸钙的引入会使聚合反应速率有不同程度的降低；使用1%～5%的TMPTMA或DVB，可实现PS对碳酸钙颗粒的牢固包覆，不可抽提的PS达94%以上；当碳酸钙用量改变时，需要适当调整乳化剂和多乙烯基单体的用量；IR和TGA的结果表明，随着碳酸钙用量增加，产物中的碳酸钙含量也相应增加；TEM照片和计算结果显示，当碳酸钙用量为14.8%时，绝大部分碳酸钙颗粒被包覆，且基本上每个乳胶粒中包覆一个碳酸钙颗粒，复合粒子具有清晰的核壳结构，壳层厚度约为10 nm，而当碳酸钙用量增加到29.3%和58.7%时，壳层厚度减小，并且出现较多裸露的碳酸钙颗粒。

The fungicidal activity of methanol extract was higher than that of ethyl acetate extract, and the inhibition rates were higher than 90% against Alternaria longipes, Fusarium oxysporium, Gibberella zeae, Glomerella cingulata, Exserohilum turcicum under the concentration of 1000g/mL The results of the inhibition of spore germination indicated that the fermentation products exhibited obvious inhibition rate against Alternaria longipes, Exserohilum turcicum and Fusarium coeruleum, the EC50 values was 59.4g/mL, 96.5g/mL and 132.5g/mL. In the bioassay of the fermentation products against Bacillus sub tills and Bacillus cereus, by means of detection fo inhibition zone, the inhibition zone diameter was 20mm and 27mm. The results of pot tests that methanol extract showed higher than 70% of protective efficacy and therapeutic efficacy against wheat powdery mildew under the concentration of 2000g/mL.

其中，甲醇提取物的抑菌活性比乙酸乙酯提取物强，在1000g/mL浓度下对烟草赤星病菌、马铃薯干腐病菌、小麦赤霉病菌、苹果炭疽病菌、玉米大斑病菌的菌丝生长抑制率均大于90%；抑制孢子萌发法试验结果表明，2K3菌株菌丝体的甲醇提取物对烟草赤星病菌玉米大斑病菌和马铃薯干腐病菌的EC50分别为59.4g/mL、96.5g/mL和132.5g/mL；管碟法生测结果表明，2K3菌株菌丝体的甲醇提取物对枯草芽孢杆菌和蜡状芽孢杆菌的抑菌圈直径分别为20mm和27mm；盆栽试验结果表明，2K3菌株菌丝体的甲醇提取物在2000g/mL浓度下对小麦白粉病的治疗和保护作用均在70%以上。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了