结构单元

The accumulation of asphaltene in the system depends on the physical structure of ...

在沥青质分子单元叠积过程中，由沥青质的杂原子因素、过渡金属因素、芳香环结构因素和脂肪性侧链因素共同决定的化学作用的影响是第一位的，其中芳香环结构因素和杂原子因素的影响最为显著，而由稠油体系不稳定性构成的物理作用的影响则居于次要地位。

This paper mainly inverses the S wave factor using the surface wave attenuation characters. The result shows that the lateral and vertical variations of Qβ are very clear in the whole area and the asthenosphere, and some big structure area is also shown very clearly.

结果显示：研究区域的Qβ横向和纵向变化非常显著，能够明显区分软流圈结构，各个大构造单元的Qβ结构呈现出显著的变化。

Composite stainless steel tube optical fiber unit,PDPE inner sheath,medium carbon steel wire armour,Ditumen coati.........

浅海光缆典型结构中心管式单层铠装结构产品型号 SOFC－ADK/4～96SM 不锈钢管光纤单元，聚乙烯绝缘内护套，钢丝铠装，沥青浇灌，聚丙烯绳外被。

The existence of zig-zag transformer and the complexity of topology make the simulation of commode voltage very difficult.

由于此结构中存在变压器，且每相由多个H桥单元串联而成，拓扑结构复杂，为共模电压的分析增加了难度。

Experimental results show that the operation voltage can be as much as 4V less than that of conventional full F-N tunneling NAND memory cells.

测试结果表明该结构的工作电压比传统NAND结构的存储器单元降低了4V。

With thw cubic B spline function treated as displacements, the spline element stiffness matrix is established based on the principle of minimum potential energy.

用3次B样条函数来构造结构的位移模式，基于最小势能原理导出了桥梁结构的样条单元刚度矩阵。

The vibration modes of the structure are calculated by dispersing the structure with different element.

用不同的单元将结构离散，计算了结构的振动模态。

The paper mainly discusses the distinguishing usage of the isoparamentric transformation idea to deal with complicated physiological structure, such method as fibrous finite element division, material parameter transformation concerned non-homogeneity, numerical integral with multi-layered composite, and inverse mapping considered complex boundary condition and loads.

本文主要介绍了等参变换思想、方法在建模分析中的特色应用，如基于纤维结构的等参有限单元离散、考虑非均匀性的材料参数等参变换、层和数值积分和考虑复杂边界条件及负载特性的逆变换等均是运用等参变换的思路来处理复杂的生理结构问题。

Details punching process different forms of the characteristics and difficulties, an analysis of the tubes in the process of punching force and deformation of the tube, giving details of the tube clamping and reverse punch the need for pre-deformation and design methods, introduction of specific modules can be combined Guanzi punching die structure design and manufacture of key components, the introduction of simple structure, low manufacturing costs, assembly convenience of fast and flexible, applicable to many varieties, short-cycle preparation and application of the superiority of the scope of After the structure of the tube to improve the punching mold, significantly broadens the scope of the existing pipe punching process and the application of mold capacity.

工程类的汉译英，帮忙翻译下谢谢详述了管子冲孔工艺不同形式的特点和难点，分析了管子冲孔过程中的受力情况以及对管子变形的影响，详述了管子冲孔夹紧及反向预变形的必要性和设计方法，具体介绍了单元可组合式管子冲孔模具结构的设计及关键零件的制造，介绍了具有结构简单、制造成本低、组装方便快速灵活、适用多品种、准备周期短的优越性及应用范围，经过结构改进的管子冲孔模，大大拓宽了现有管子冲孔工艺范围和模具的适用能力。问题补充：请不要用在线翻译的功能搞，翻得很不好

We trace back to the history of philosophical inquisitions and scientific research for matter structure, and point out that quarks are the basic elements of matter.

追溯了物质结构的哲学探讨与科学探索，指出了夸克是物质结构的最小单元，从而揭开了物质结构之谜。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。