结构公式

Rationality and feasibility of the theoretical model is proved by the results of experiment and calculation, and achieved the relation formula of cord tension with structure of tire and case.

通过试验和理论方法修正轮胎帘线张力与轮胎结构参数及静载工况条件的关系公式。

This research job analysised the extending roll pass system the finish roll pass system and the ultimate roll groove. The mathematical models and experience formulations used for roll pass design are corrected according to the basic theory and the practical experience of the engineerings. The thread steel bar CARD was set up with the visual program tool-VisualBasic6.0, based on the method of the structural program design.

本课题通过对螺纹钢延伸孔型系统、精轧孔型系统及成品孔型的构成和设计方法的分析，结合螺纹钢孔型系统的基本设计理论和工程技术人员的实际生产经验，对以往孔型设计过程中所使用的数学模型、经验公式等进行了修正，以结构化程序设计方法为基础，采用可视化编程工具VisualBasic6.0建立了螺纹钢计算机辅助孔型设计系统。

Keywords cold-formed steel;residential building;steel frame;wallboard bracing;wall stud system;elastic springs model;finite element analysis;centric axial loads;full-scale test;effective length factor;simplifi

Article From 同济大学；结构工程博士论文 2006年度冷弯薄壁型钢；低层住宅；钢骨架；墙板支撑；墙柱体系；弹簧模型；有限元分析；轴心荷载；足尺试验；计算长度系数；简化设计公式

The equation and method used to determine the thickness of steel plate under impulsive load is established.

对脉冲荷载下的粘钢加固混凝土结构，建立了用于确定钢板厚度的公式和方法。

By putting forward the concept of the superimposed effect of the stress dispersion, this paper has pointed out that there was a minimum reinforced space, and gave the formula of it at this foundation.

本文提出扩散应力&叠加效应&的概念，指出在加筋土结构中存在最小加筋间距，在此基础上给出最小加筋间距的计算公式。

At the beginning of the thesis, the structure of usually used radome is introduced and the parameters of electromagntic characters are described in Chapter Ⅰ; the different methods for analysis of the electromagnetic characters of radome are summarized in Chapter Ⅱ; the propagation of 3-D beam in free space is conducted in Chapter Ⅲ; then in Chapter Ⅳ, the 3-D Complex Ray Theory are analyzed and the characters of transmitted field of sum and difference beams through radome are studied, and the relative formulations of calculation are rekened; at last the electromagnetic characters of the ellipsoidal sandwich radome and the plane single-layered radome are discussed, and suggestions for optimization of electromagnetic properties of radome are given.

本文第一章介绍了常用雷达罩的结构和描述雷达罩电磁特性的参量，第二章概述了目前分析雷达罩电磁特性所采用的各种方法，第三章分析了三维波束在自由空间传输特性，第四章研究了三维复射线理论，并应用它分析了单脉冲和差波束穿过雷达罩透射场的特性，导出了有关计算公式，在第五章，通过大量的数值计算和实验研究，讨论了椭球形三层夹心状实用雷达罩和单层介质平板模拟雷达罩的电磁特性，并提供了雷达罩电气特性优化的建议。

The paper also gives a simplified formula which is coordinated with the current concrete structure design code, and the effect of steel on the shear strength is described.

此外，本文还给出了与现行混凝土结构设计规范相协调的简化计算公式，并对钢骨对承载力的影响进行了分析。

The VCL method and the displacement method are used to calculate the Stress Intensity Factors of semi-elliptical surface crack at the root of pipe screws, on the basis of which a simplified calculating model for screws contact is put forward so as to analyse the fracture intensity for oil drill pipe screw coupling. For the semi-elliptical surface crack with different shape and deep ratio at the root of female and male screws and the corner of male flange, the SIF has been studied systemically under inter-pressure, tension, bend and torsion loads and the approximate formulas encluding the structure parameters of oil drill pipe screw coupling, deep ratio and the shape parameters of surface crack are developed.

对工程实际中的多种石油钻杆接头螺纹连接件，就公螺纹齿根、母螺纹齿根、公螺纹台阶转角处存在的不同形状、不同厚度比的半椭圆表面裂纹，在拉伸、内压、弯曲、扭转多种载荷作用下的应力强度因子作了系统研究，在大量有限元计算基础上，建立了包含接头结构参数、裂纹形状、厚度比在内的近似计算公式。

To reveal the complicated stress state of masonry structure in project and the effect of normal stress on shearing behavior,failure form and shearing strength,the shearing strength was obtained through experiments on 54 pieces of minitype sand-lime autoclaved aerated concrete masonry subjected to different normal stress.

为了解砌体结构在实际工程中所处的剪压复合的复杂受力状态，作用在砌体上的正应力对砌体的抗剪性能、砌体的剪切破坏形态及其对砌体抗剪强度的影响，对54个小型灰砂蒸压加气混凝土砌体进行静力抗剪试验，通过施加不同的正应力得到相应的抗剪强度；分析其破坏机理，归纳得出剪摩、剪压、斜压等破坏形态，并与砖砌体的破坏形态进行比较；根据试验结果回归分析得到灰砂蒸压加气混凝土砌体的静力剪压相关性曲线，与砖砌体的剪压相关性曲线进行对比分析，得到两者的异同；在静力剪压相关性曲线的基础上，依据变摩擦系数的剪摩理论，提出灰砂蒸压加气混凝土砌体静力抗剪强度的建议公式，并对摩擦系数进行了简化

An automatic arc welding machine for saddle joint seam on large diameter cylinders was designed and its structure,components,characteristic and working principle were discribed in this paper.

介绍了大直径筒体马鞍形接缝自动焊机的结构和工作原理，以及设计的主要特点。推导出了该系统用来控制气体保护电弧焊焊枪运动轨迹的关键部件──凸轮的形状与尺寸的计算公式：l =l′-Z′=l′- [(R2 -r2 cos2 ψ) 1/ 2 -rsinψcosα]/sinα。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。