结合强度

The shearing failure of structural plane is considered to be corresponding to the maximum of real contact area, a criterion is given to distinguish the shearing failure of structural plane and a new select method of shear strength is brought forward subsequently; Examine the influence of geometrical features and thickness of weak intercalation on the integrative strength of weak structural plane based on the composing of basic strengths, formative mechanism of shearing plane and failure pattern; and present the quantitative relation between the strength and thickness.

4详细研究了依附型滑动面中的硬性结构面和软弱结构面力学特性和破坏模式，对硬性结构面引入摩擦学中的粘着摩擦理论，着重研究结构面在剪切过程中实际接触面的变化规律，提出实际接触面积的最大点即为强度破坏点，并结合实际数据进行了验证；对软弱结构面则从其基本强度的组成、内部剪切面的形成机理和破坏模式入手，研究了结构面的几何特性、夹层厚度和强度关系对软弱结构面综合强度值的影响，并给出了定量关系式。

In this project, the selection criteria of matrix and reinforcement for obtaining composites with high strength and toughness are determined. The as-cast and aged microstructures of composites reinforced with particles of different strength are observed, and their metallurgical conditions and stabilization mechanisms are analyzed. The aging precipitation behaviors and mechanisms are studied. Some characteristics of nano-materials (micro-distortion areas) are found in 150nm- Al2O3p/Al composites and their formation mechanisms are expatiated. The "flexible" restriction to the deformation of the matrix by low strength AlN particle is observed by in-situ TEM and SEM techniques, and the mechanisms of its resist on cracks propagation and its contribution to composite strength are revealed. The high temperature deformation behaviors of Al2O3p/Al composites are studied. A rare-earth coating is established on sub-micron Al2O3 particles, leading to an improvement in wettability between coated Al2O3 and liquid aluminum and a decrease in infiltration pressure. The strength and ductility of coated particles reinforced composite are also increased. The interfacial characteristics, bonding structures and their formation mechanisms are studied, and the crystal orientation relationships between reinforcement particles and aluminum matrix are investigated. Finally a lighter composite with better balance of strength and damping properties is reinforced with hollow ceramic microballoons of ultra-lower strength.

本项目发现了获得高强度和高韧性复合材料的基体、增强体选择依据；观察了各种强度质点增强复合材料的铸态和时效态微观组织，分析其微观结构形成的金属学条件及稳定性机理，研究了其时效析出规律和时效机制，发现了150nmAl2O3颗粒增强铝基复合材料基体中的纳米材料特征，并解释了其形成机理；利用TEM和SEM动态拉伸技术发现了低强度质点AlN颗粒对变形协调的&柔性强化&机制，揭示了其对裂纹扩展的阻碍作用和对复合材料高强度的贡献；研究了中强度质点的Al2O3颗粒增强铝基复合材料的高温变形行为，并对其进行了稀土界面层设计与制备，改善了颗粒与铝合金之间的界面润湿性，降低了复合材料铸造渗透压力，提高了复合材料的强、韧性；研究了多种复合材料界面结构及形成机理，确定了增强体与基体之间的界面结合机制，分析了复合材料界面处的晶体学位向关系；最后制备了含微孔的中空型陶瓷颗粒增强的特种复合材料，得到了强度和阻尼综合性能较好的轻质复合材料。

After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

Introduce the cohesion-friction model of rock strength theory, and extend the model to select the strength of sliding plane, discuss the variation rules of peak strength and residual strength under different normal stress, and then present the selection model of shearing strength. After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

The gradient PPS/FEP composite anti-corrosive coatings were prepared on carbon steel. The bonding strength of all coating systems was determined by the pull-off test.

在碳钢表面制备了具有梯度结构的PPS/FEP复合防腐蚀涂层，采用拉开法测定了各涂层体系的结合强度。

Methods Ten laser welded CW-PA ceramo-alloy rods were fused with porcelain at fusion zone. The porcelain-metal bond strength was measured with pull-through test. SEM examination and EDAX analysis were performed.

方法将10个激光焊接的CW-PA烤瓷合金试棒在焊缝熔区烤上瓷盘，做棒盘实验，测量金瓷结合强度，并做扫描电镜观察和X衍射能谱分析。

The showing up ofCV explain that there are a few graphite that make the arrangement of cell wallof wood more orderly and increase the combination power,the surface hardness,and abrasion degree.

CV价态的出现，说明有少量石墨碳存在，从而使木材细胞壁物质排列更加有序，结合强度提高，木材表面硬度和耐磨耗度增大。

Abundant of VST, CPT, DMT tests data and the finite element analysis result are applied to get the distribution and increasing rule of strength of silt in consolidation process. The relation between the strength and depth is linear before and after consolidation. The strength-increasing rates are different in different horizontal places.

通过大量的十字板剪切试验、静力触探试验和扁铲侧胀试验，并结合有限元分析结果，研究了淤泥抗剪强度的分布规律和排水固结过程中抗剪强度的增长规律，发现排水固结前后淤泥路基强度基本随深度增加线性增长，排水固结过程中水平方向的抗剪强度增长速度不同。

XRD and EDS analysis indicate that at static condition, the composition of the scale is CO3, while the scale changes to CO3 at dynamic conditions. The increment in flow rate increased the thickness of the scale remarkably, but had little influence on the hardness and Young's modulus of the scale. The fracture toughness of the scale exhibited the lowest value at the flow rate of 0.5 m/s whereas the adhesion strength increased with increasing the flow rate.

结果表明，静态条件下形成的腐蚀产物膜的主要成分为CO3，动态条件下的主要成分为CO3；介质的流动能够促进腐蚀产物膜的形成，但对膜的硬度以及杨氏模量影响不大；腐蚀产物膜的断裂韧性随着流速的增大先下降后上升，流动状态下内层腐蚀产物膜的致密性较好，膜与基体的结合强度较高。

The good adhesion of the NDFs on silica or optical glass substrates is beneficial for the applications of the NDFs as protective coatings on optical devices and mechanical matings.

石英玻璃和光学玻璃上生长的NDF与衬底间具有较高的结合强度，有利于NDF作为光学器件和机械部件保护膜应用。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。