约束的

The constraint handling is one of the major concerns when applying genetic algorithms to solve constrained optimization problems.

对约束条件的处理是应用遗传算法求解约束问题所涉及的一个主要内容。

But this is bound to the outside world entrepreneurs and business constraints, there is no way.

但现在这种约束是外界对企业家和企业界的约束，是没有办法的。

On the basis of general Krawczyk-Hansen Operator, the interval iteration of the constrained functions are established; the interval extension of maximum entropy function is discussed; convergence is proved; region deletion rules are supplied and the algorithm of interval maximum entropy has been set up.

利用极大熵函数和罚函数将问题转化为无约束可微优化问题，借助广义Krawczyk-Hansen算子建立了约束函数的区间迭代；讨论了极大熵函数和罚函数的区间扩张，证明了收敛性等性质，给出了无解区域删除原则，建立了区间极大熵算法。

Taking the unknown coordinate in curved surface and curve as design variables, the equation of curved surface as constrained condition, and the distance between unknown coordinate as objective function, optimization is proposed to minimize the distance between curved surface and curve.

建立以曲面、曲线上未知，点坐标设计变量，以曲面和曲线方程为约束条件，以曲线和曲面距离为目标函数的约束优化方法来精确地确定曲面和曲线之间最短距离，同时确定获得最短距离对应的坐标点。

With the constraints of these feature points, perspective projection, coplanarity and colinearity, the curved surfaces can be recovered by minimizing the linearly constrained quadric objective function.

把特征点的位置、共面、共线、透视投影等作为约束，通过最小化线性约束下的二次目标函数实现曲面重建。

The first level and the lower level both have their objective functions and constraint conditions, the objective function and constraint conditions of the first level not only have relations with the upper decision variable, but also depends on the optimal value of the lower level.

上层和下层各有目标函数和约束条件，上层问题的目标函数和约束条件，不仅与上层决策变量有关，而且还依赖于下层问题的最优解或最优值。

When you remove a deferrable constraint, its index remains.

当用户移除一个可延迟的约束时，此约束使用的索引仍将被保留。

It is also presented that DP model can be used to support model derivation.

首次提出用约束实现对DP模型的描述，建立了相应的约束描述机制。

Through the suitable selection of difference quotient and correction of the one-dimension inaccuracy linear searching,scope of the improved method is extended.

从应用角度出发，首先，将约束变尺度法改进为一般约束条件，通过适当选择差商形式和对一维不精确线性搜索方法的修正，扩大了该方法的适用范围。

The first one is an algorithm with terminal sliding mode equality constraint. The second is a dual-mode control scheme, which enlarge the terminal region. The sliding mode based MPC is implemented while system state is outside of terminal region, and sliding mode variable structure control designed off-line is used once system state arrives in the terminal region.

第一种方法为终端滑模等式约束非线性模型预测控制方法，首先离线设计切换函数使得滑动模态渐近稳定，然后在有限预测时域的基础上对切换函数附加一个终端等式约束；第二种方法为双模控制方案，在终端区外采用模型预测控制，使得系统状态在有限时域内到达终端区内；在终端区内部采用离线设计的滑模变结构控制，使得系统渐近稳定。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。