约束

According to the experiment results together with the existed strength equation of FRP tubesconfined concrete,the strength model of the GFRP tubed short reinforced concrete columnsand the ultimate beating capacity of the composite short columns are proposed.

根据试验结果及现有FRP管约束混凝土强度计算公式，提出了GFRP套管约束钢筋混凝土轴压强度的计算公式与组合短柱承载力计算公式，计算结果与试验结果吻合良好。

By the analysis of the characteristic and restriction of the gear components ,this paper upbuilds the characteristic model based on the restriction and actualizes data transmission and information sharing among CAD.CAE and CAPP .This paper analyzes the general principle of parameter determination and strength check about gear and researches the algorithmic of gear strength check based on the characteristic .This paper introduces expert knowledge into respective procedure of CAD.CAE and CAPP and actualizes the intellectualization in design process .strength analysis and process planning .

以齿轮类零件作为研究对象，在分析了其特征及约束的基础上，利用数据库技术和图形单元建模技术，建立了基于约束的特征模型，实现了CAD／CAE／CAPP之间的数据传输和信息共享；分析了齿轮参数确定、强度校核的一般原则，进行基于特征的齿轮强度校核的算法研究；将专家知识融入在CAD、CAE、CAPP各个过程中实现了设计过程、强度分析和工艺分析的智能化。

Right-click the constraint Angle SHAFT TURN (180.00 deg) and clear the Suppress box to activate the constraint.

在约束 「Angle SHAFT TURN (180.00 度)」上按一下右键，并清除「抑制」方块以启用约束。

Chapter 5 solves the difficult degree-constrained minimum spanning tree problem by ant algorithm. Large number of tests and comparisons show the effectiveness of the searching strategy for highly constrained problem instances.

第五章对度约束最小生成树问题这个难题设计了相应的蚂蚁算法，通过大量试验求解并与其他算法作比较，发现这种蚂蚁搜索策略对于约束条件苛刻的问题实例来说，效果十分明显。

From the angle critical force ,this thesis analyses the stability of the formation of axle shaft spline in the extrusion and the calculation of the constraints available after losing stability.

从临界力的角度入手分析花键半轴在挤压成形时的稳定性及失稳后可增加约束的计算，研究表明半轴花键实现精密挤压成形不稳定时可增加约束来解决失稳问题。

Finally, a simplified method is also presented to solve the constraints system problem. This method can simplify the liner constraints inequality group effectively.

论文最后还提出了一种线性约束系统的简化求解算法，可以使线性约束不等式组的求解简单化。

At the end of this paper Ⅰ conclude the three points that shared by the reflexives of the both languages: a reflexive must be bound in it binding domain, a reflexive cannot take a nominative case, and the binding domain of a reflexive cannot be bigger than a sentence.

於是我们便可归纳出英语和汉语中的反身代名词共通特性为：反身代名词必有约束范围；反身代名词不可居於主格格位；且反身代名词的约束范围不可超过句子。

The three dimensional model on engine block combination structure of a piston engine is established by the ANSYS software,and the modal analysis is carried out in the case of constrained model.

采用ANSYS软件对某活塞发动机机体和缸盖的组合结构进行了约束模态的有限元分析，得到了机体组合结构的前20阶约束模态的固有频率及相应振型。

In order to realize the product disassembly planning, the method of judging adjacency point is proposed based on the analysis of disassembly sequence generation. Based on the disassembly logic inference, the combine of Deep-Searching and Wide-Searching, the product disassembly sequence algorithm is generated.

其次，为了实现产品拆卸序列规划，在研究利用产品拆卸约束图生成产品拆卸序列的基础上，根据产品拆卸约束解除的逻辑推理，运用深度优先与广度优先搜索策略，给出目标拆卸序列生成算法，并运用遗传算法对生成的拆卸序列进行优化。

This paper draw the Critical Chain Technology based on Theory Of Constraint to make the network schedule plan, promote the resource constraint to activity logical relations with the same level, indicate to replace the Critical Path by Critical Chain.

本文将基于约束理论的关键链技术引入网络进度计划的编制中，将资源约束提升到与工序逻辑关系同等的高度，主张采用关键链取代关键路线。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。