系统函数

The practical application and computer simulation research show that the application of BP neural network to real-time diagnosis and modeling for optimizing WOB is practicable and efficacious.

BP网络作为一种非线性映射，可以逼近任意的非线性函数，所以它不仅适用线性系统，也适用非线性系统。本文选用BP网络作为钻进过程实时事故诊断和建立钻压优化模型的工具。一般B

Considering the characteristics of multi-variables and multi-objectives in the burnup calculation process of nuclear system, the optimization control method based on GA is presented as a functional module of the multi-functional transport/bu...

利用FDS课题组开发的多功能中子学程序系统VisualBUS1.0，针对该系统燃耗计算过程具有多变量和多目标函数复杂关系的特点，应用遗传算法对嬗变包层的锕系废料嬗变区的初装料量进行了优化处理，使其在一定的物理和工程参数约束下，指导嬗变区的装料份额取值，分析嬗变区的装料份额对锕系废料的年燃耗深度等参数的影响。

This paper set up a hardware in the loop and real-time simulate test system of 1/4 vehicle suspension.

摘要本文构建了1／4汽车半主动悬架的硬件在环实时仿真试验系统，将S函数编程实现的线性滤波和谐波叠加模拟产生的随机路面激励用于该试验系统中，进行了时间域内路面不平度、磁流变阻尼器、被动悬架和半主动悬架的仿真及试验，采用性能评价指标对悬架性能进行评价，比较优劣。

This paper set up a hardware in the loop and real-time simulate test system of 1/4 vehicle suspension.

本文构建了1／4汽车半主动悬架的硬件在环实时仿真试验系统，将S函数编程实现的线性滤波和谐波叠加模拟产生的随机路面激励用于该试验系统中，进行了时间域内路面不平度、磁流变阻尼器、被动悬架和半主动悬架的仿真及试验，采用性能评价指标对悬架性能进行评价，比较优劣。

Energy of any type disperses from being localized to becoming spread out*, if it is not constrained.

克劳修斯熵只对系统的平衡状态才有意义，它是系统平衡状态的函数。

AR model is applied to identify the noise source for enigne. Through the results of noise signal process, it shows that it is practical and credible to use AR model to study engine noise. Through the theoretical analysis, according to the specific engine structure, the SEA equation is formulized. The method of SEA sensitivity is brought forward on the basis of the sound power function.

从理论分析入手，结合具体的发动机产品结构，建立了结构噪声分析的统计能量方程，提出了基于声功率函数的统计能量灵敏度分析方法，把发动机的外在表现和内在因素直接联系起来，分析了系统主要参数对系统声功率的影响程度，得出了一些实用性的定性结论。

The restriction function of complex machine non-tree system isgiven, the restriction of non-tree system is raveled, and the dynamic modeling of non-tree system

摘 要：根据复杂机电动力学系统的特点，提出了一种约束函数递推组集法的复杂机电系统全局建模方法。

3D-CTM (Coupled Thermo-Mechanical Forming Simulation) software for precision forging process of aero-engine blade was developed. The key technologies of 3D coupled rigid-viscoplastic thermo-mechanical FEM simulation of blade forging process were studied systematically. By using the remeshing method of contracting from the boundary to the inner, new mesh system from old distorted mesh system can be obtained. A method of modifying the position of nodes touching on the die according to its original normal was proposed to avoid "dead lock" problem due to uncontinuity of normal of scatted die meshes. The pseudo-static iterative algorithm was used to simplify the coupled thermo-mechanical computation. In particular, formulations to determine relaxation factor β was established for rigid viscoplastic FEM adopting penalty function method, and an improved cubic factor rapid algorithm derived from these formulations was proposed by combining with the advantage of advance and retreat search method.

采用基于边界构形的内缩法，实现了三维畸变网格的重新划分；提出了初矢修正法对触模节点的位置进行修正，解决了由于离散的模具网格的法矢不连续造成的&死锁&问题；采用准静态迭代法简化了速度场和温度场耦合计算过程；特别是针对减速因子β的选取，建立了适用于三维复杂成形过程刚粘塑性罚函数法有限元三次因子法的计算公式，并结合进退搜索法提出了改进的三次因子快速算法，提高了模拟计算效率和稳定性，在此基础之上，开发了面向叶片精锻过程的三维刚粘塑性热力耦合有限元模拟分析系统(3D-CTM)，系统的可靠性得到了圆柱体镦粗的验证。

In this paper the rocket of 122mm, 20km is exampled, CADET is used in random ballistics system with the action of random wind by use of sharping filter when the differential equations of sharping filter and angle motion equations of ballistics are allied.

以某火箭弹为例，在随机风场作用下，利用纵风作用下的随机弹道系统成形滤波器，把成形滤波器的微分方程和外弹道角运动方程联立，对此系统采用协方差分析描述函数法，对火箭弹的散布进行了计算。

For single input single output linear system, its zeros were determined by the output function of system.

摘 要 对于单输入-单输出系统，它的零点取决于系统的输出函数。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。