精度

Aimed at getting rid of big bulk, low precision, limited secular stability and high cost price the single star simulator used to be, while based on the practical demands in single star simulator project and combining with the technical specifications of star sensor for user, the paper proposes to use high stability adjusted digital light source as the core elements of the single star simulator, and describes development methods and development technologies for the whole system of the single star simulator from the view of project application.

论文主要针对过去研制的单星模拟器体积大、精度低、长期稳定性不够、成本高等缺点，结合单星模拟器的工程使用实际需要和用户星敏感器的技术指标要求，提出了一种数字式光源的设计方法，采用闭环控制并使用大规模集成电路模块，减小了光源体积(光源由三块核心电路板组成，尺寸分别110mm×110mm、100mm×100mm和30mm×30mm)提高了光源精度、提升了光源稳定性(光源连续工作8小时内的误差15.848%)和降低了光源成本，在此基础上，实现对以往单星模拟器诸多缺点的改进。

Based on relative discernibility of decision table, an approach for the self-determiningβ-Value and settingβ-Value in variable precision rough sets model is proposed.

基于决策表相对可辨识性，提出变精度粗糙集模型变精度参数自主式获取和设置的方法。

The system is constructed by the five important modules including the realizations about the tolerant classes based on tolerant relation in uncompleted information system, self-determining the variable precision value of variable precision rough sets model, influence of variable precision value on rules and coverage and "Gray" region.

主要包括在不完备信息系统下的相容类求解、变精度粗集模型下的变精度值自主式求解以及该模型下的规则和覆盖求解、Gray区域求解等。

The author constructed a linear schemes type Region-Project-Join-Normal-Form based on lossless join decomposition, and gave the form of RPJNF through the presentation of equivalence between semantic variable independence and syntax variable independence under finite precision domain. Some other new constraint data dependencies including partitioned multi-region existence dependency and single region existence dependency were also presented. A result of variables set under linear transformation was discussed.

文中给出并证明了多区域存在依赖满足的几条推理规则；提出并证明了线性序约束关系进行模式无损连接分解的充要条件是变量集满足变量独立和多区域存在依赖；设计了一种基于模式无损连接分解的区域投影连接范式；通过证明有限精度域上语义变量独立和语法变量独立的等价性，给出有限精度域上RPJ范式的表达形式。

The improvement is 45% for the phase-lag of S2 after assimilating the altimetric data of the crossover points, while the correction for the diurnal constituents is not so good as for semidiurnal constituents.

利用基于最优插值法的混合法将交叉点的调和常数同化到动力模式中，同化后S_2分潮的迟角精度改进最大，可以改进45％，结果显示高度计资料的分析结果对模式结果的精度影响很大。

This thesis,starting from working out the arrest points and the infl ection points of the function curves of the grey mathema tical model GM(1:1 )and its residual correction model and residual period model, derives the conditions for empliying these grey models to obtain a higher class of accuracy,thus enabling the user to decide which model should be used in the light of the state of given initial sequency data.

从求得灰色数学模型GM(1.1)及其残差指数修正模型和残差周期修正模型函数曲线的驻点与拐点入手，导出使用这些灰色模型取得较高精度的条件，让使用者可依据初始序列数据的态势决定采用哪种数学模型，并且在结果未揭示以前便可大体上估计到拟合精度是否令人满意。

Servomechanism is one of most important subsystem of rocket, and servo valve is the core part of servomechanism. Feedback stick is a precise and low stiffness part and its machining quality and stiffness accuracy determine the accuracy and reliability of servo valve working.

伺服机构是火箭最重要的分系统之一，而伺服阀是伺服机构的核心，反馈杆是伺服阀中的精密低刚度元件，它的加工质量和刚度精度直接影响伺服阀的工作精度和可靠性。

The erosion processes from sheet erosion, rill erosion, and to gully erosion were represented as well.

结合3种测量技术从测量精度、测量人员要求、数据处理、数据通用性、配套软件使用、前期投入、测量条件等几个方面入手，对比分析高精度GPS(Trimble 5700)、三维激光扫描仪(Leica HDS 3000)和测针板的3种测量方法的优缺点，同时对3种测量方法在沟蚀过程监测和侵蚀量估算方面进行对比研究。

In practical application of numerical control lathe, the sice precision of numerical control turning can be conteolled and ensured effectively by effective steps considering the influence of geometrical Rarameters to the sice precision of numerical control turning .

在数控车床加工的实际应用中，针对刀具几何参数对数控车削加工尺寸精度的影响，采取有效的措施，使得数控车削加工的尺寸精度，得到有效的控制和保证。

ABSTRACT Satellite Laser Ranging is a technique with the highest precision for a single-shot measurement of satellites.

卫星激光测距是卫星单点测量精度最高的一种技术，目前精度为亚厘米量级。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。