精度

The boundary conditions and the latent heat of heat transfer system have been treated by heat-enthalpy method.

在这样的充填条件下，虽然金属压铸模的导热性很高，蓄热能力很强，但要求在压铸模型腔内获得形状完整、轮廓清晰、尺寸精度高的铸件，必须得选用合理的模具结构和压铸工艺，而压铸模具的尺寸精度和使用寿命在很大程度上取决于其在压铸过程中热应力和其产生的变形。

The first one is integrated by the least squares and the radical basis function interpolation, which is aimed to the slight nonlinear sensors, and under the limited increament of computation, it can make the results more precise. The second is used for serious nonlinearity and based on the moving least squares which converts the approximation generally into locally, and the result of this way is also satisfied.

对于不是特别严重的非线性，采用最小二乘拟合与径向基函数残差插值进行融合重构，可以在增加有限计算量条件下提高数据的近似精度；对于非线性较严重的传感器，为兼顾局部特性，采用移动最小二乘法进行数据重构，它通过全局近似向局部近似的转化，同样使重构结果具有满意的近似精度。

In order to improve the monitoring precision and resolution of tropospheric zenith delay, the hybrid approach, using a batch least squares estimator but parameterizing the zenith delay by a linear spline with knots at 30-minute intervals and treating the knots as a Gauss-Markov process, is employed to deal with the tropospheric zenith delay.

为了提高对流层天顶延迟的监测精度和分辨率，我们采用了分段的参数估计和随机过程相结合的估算方法来处理对流层延迟，由此获得了分辨率分别为2 h和30 min，精度好于1 cm的天顶延迟量。

In the research of image system, a image processing algorithm of welding seam is established on the basis of image math. model of structured light of Fourier-transformation of lens in space, and the image analyzing system based on the rule-model of the features of welding seam in 3D-space is also established which can meet the requirements of the auto-programming of welding parameters for arc welding robot in accuracy and reliability.

在焊缝图象系统的研制中，基于结构光空间付氏变换的光纹图象数学模型，建立了焊缝图象处理算法，并基于焊缝三维空间特征的规则模型，建立了焊缝图象分析系统，使焊缝检测与分析的精度和可靠性达到了弧焊机器人焊接参数自动规划及焊接路径自动规划的精度要求。

In general the accuracy of geoidal heights, as given by spirit levelling, much exceeds that of any other system.

一般说来，水准测量测出的大地水准面高程的精度，远远超过任何其它方法的精度。

B. when precision testing equipment, the adjustment process: in the assembly process and equipment are completely assembled to precision testing and adjustment, such as boring bed in the installation process after grinding levelness and straightness calibration, an adjustment and measurement and cannot fully reflect the true error, and requires at least three times and measurement, can eliminate stress, and each must adjust time intervals, it takes about three days.

B。设备精度检测时的调整过程：设备在组装过程中及完全组装后均需进行精度检测及调整，如对镗床床身导轨磨削后在安装过程中的水平度和直线度的校验，一次调整与测量并不能完全反映出其真实误差，而至少需要三次调整和测量，才能消除应力的影响，且每次调整都需有时间间隔，故需时约3天。

And the error limit of flux sensor under 5%, the error limit of intelligent Heat Meter up to grade 2 according to the precision criterion of heat meters.

基于MSP430单片机的智能热量表满足《中华人民共和国城镇建设行业标准CJ128-2000热量表》的标准要求，电源采用内装3.6V锂电池，使用寿命超过八年；流量传感器误差限不超过5％，总体热量表精度达到2级精度标准。

In recent years, with the development of the micro-electronics technique, the price of GPS receiver have been greatly falling , and as a result of the United States closing SA to stop limiting the public position accuracy of GPS , the GPS positioning accuracy have improved greatly in public field. All this consumedly promote the development of GPS in public field, and especially in the vehicle navigation field , GPS shows its superiorly navigation performance.

近年来随着微电子技术的发展使得GPS接收机的价格大幅度下降，同时美国提前关闭SA停止对民间用户精度的限制使得GPS民用定位精度有了很大的提高，这大大促进了GPS在民用领域的发展，尤其是在车辆导航领域，GPS系统充分展示了它那优越的导航性能。

Some methods based on statistics for dimensional position and data processing by such software as Excel are suggested for the calibration of the dimensional angle shown by a dynamic target using linear matrix CCD and video interpretation.

动态旋转靶标可以给出检测光电测量设备跟踪精度和测量精度的空间角度真值，针对动态靶标的空间角度标定问题提出了基于线阵CCD标定和视频判读标定的方法。

Based on a profound study of the variation law of phase difference between two periodic signals and the ordinary frequency measurement method, this paper presents a new method for comparing frequency standards, which is based on the Lissajous figure.

用传统的李沙育图形法是不能完成对高精度频标比对的，但将等效鉴相频率这一新概念引进，可以使得本来不能完成的高精度频率标准的比对变为可能。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。