粘度

Transport properties including the coefficients of self-diffusion, viscosities, and conductivities were also studied and compared.

系统地研究并比较了离子液体的扩散性质，包括体系阴阳离子的自扩散系数、粘度及电导率。

Using molecular dynamics simulation method, this project carried out intensive studies on these two aspects and their relationship. Melting point, density,specific heat,self-diffusion coefficient and viscosity were involved during simulation of thermophysical properties.

本项目利用分子动力学对液态金属的热物理性质（包括熔点、比热、密度、自扩散系数和粘度）、结构以及二者之间的关系进行了研究。

Choosing modified corn starch of self-preparation as standard sample,its viscosity and translucent rate were checked and the data is linear fitted.

选用自制的变性淀粉作为样本，检测样本浆液的透光率与粘度，将所得到的数据进行线性拟合。

The produced water which was made by crude oil dehydration containing polymer, alkaline and surfactant, brought many technique problems in the water treatment process system, this made the polymer flooding and water flooding water treatment technologies difficult to suit to the disposal requirement of the special water. The developed experiment research indicated that: because of the surfactant, the semidiameter of the oil droplets in the ASP flooding is much smaller than that in polymer flooding, and the stability of the oil droplets is higher than that in polymer flooding, The viscosity and combine difficulty of the oil droplets increased, and all the changes of speciality resulted in the increased difficulty in the ASP flooding produced water disposal.

三元复合驱采出液经脱水后得到的采出水中，因含有聚合物、碱和表面活性剂，给采出水处理工艺系统带来了一系列的技术问题，使已经应用于水驱和聚合物驱采出水处理的技术难以适应这种特性的采出水的处理要求，已经开展的实验研究表明：三元复合驱采出水中由于表面活性剂的存在，使采出水中油珠的粒径远远小于聚合物驱采出水，油珠的稳定性明显大于聚合物驱采出水；由于聚合物的存在，采出水粘度增大，使油珠聚并难度增大，这些特性的变化造成三元复合驱含油污水的处理难度大于聚合物驱。

The results of canonical correlation analysis indicated that general evaluation of sensory organ and eating viscosity had the most significant effect on the canonical variables.

对所得结果典型相关分析说明，在酸乳的6项质量指标中，酸乳的感官综合评分和食用粘度对典型变量的影响力最大，是最值得重视的因素，而胞外多糖的含量不是重要因素。

Plastic should lower 3 steps, because plastic is a step to add meltresin material to cyclinder , Higher stick of resin material ,higher screwback pressure. Screw speed differs depending on decomposing temperatureof resin material ,Higher screw speed ,Higher trim force of resin,higher cyclinder temperature. Some resin material may decomposes so it setscrew speed in mid-speed such as 45-75%, In plastic step setting screwback pressure is very important, Higher screw back pressure ,higherquality of product screw back pressure make resin structure order, Moldingproduct is beautiful and volume stable. But ,it maybe flow if screw

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Objective To study the regularities of RBCs in the membrane shear elastic modulus and membrane viscosity.

目的 研究新生红细胞从产生到死亡过程，红细胞膜剪切弹性模量及表面粘度的变化。

It was found that the membrane shear elastic modulus and membrane viscosity decreased in this process of changing. This finding may have some basic theoretical and clinical significance.

这对研究由于贫血等原因造成的网织红细胞增多情况下全血的微观流变学特性有重要的临床意义，同时对新生网织红细胞在转化过程中膜的剪切弹性模量和表面粘度的变化规律加以系统研究，具有重要的基础理论研究价值。

Dynamic rheological test was introduced and the dynamic shearing modulus G', the loss modulus Gand the complex viscosity of coatings were measured.

把流变动态测试引入铸型涂料的研究，测量出了铸型涂料的动态剪切模量G〓、损耗模量G〓和复合粘度η〓。

Interfacial shearing elastic modulus and interfacial shearing viscosity increased to 4.958mN/m and 3.9244mN ?

2三元复合驱采出液水相视粘度随着聚合物含量和相对分子质量的增加而增大。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。