粗糙表面

The research indicated that the main electric particles forming guiding discharge channel were the electrons released from the process of the breaking up of the negative ions. During 10 microseconds after the laser pulse, the electrode also could guide discharge effectively; and it suggested the new conception of the electrode erosion, and developed new-type running disk electrode, which could discharge for a million times in atmosphere. It also suggested methods of the texturing roller of besmearing with oil film and cathodal discharge in processing. The research of the texturing roller indicated that roughness of 14 microns and the intensified depth of over 200 microns could be got.

研究表明：形成诱导放电通道的带电粒子主要是负离子解离过程释放的电子，在激光脉冲结束后10微秒内，电极都能有效诱导放电；提出了电极损耗的新概念，并研制了新型转动圆盘电极，可在大气中完成上百万次放电，提出了加工过程中负极性放电、工件表面涂介质薄膜放电的毛化工艺方法；并用之对轧辊试件进行了毛化工艺研究，毛化粗糙度可达14微米，强化深度大于200微米。

A circumferential surface roughness of about 1.0 to 3.0 is applied.

提供约为1.0－3.0微米的周向表面粗糙度。

On the basis of study on two projects:"10-DOF ultrasonic detection system for complex surfaces part" and "Ultrasonic water-logging automatic survey system for rods", this thesis studies the technologies of ultrasonic measurement, kinematic and dynamic modeling of 10-DOF ultrasonic system, real-time sensitivity auto-adjusting, integrated technology of ultrasonic measurement, surface construction and ultrasonic detection for complex surface parts and rods, thus improving the accuracy and efficiency of ultrasonic detection for parts of complex surfaces. Meanwhile, an auto-detection system for metal rods with rough surfaces and bad columniform accuracy is presented for the first time.

本文结合&10自由度复杂曲面超声检测系统&和&棒材水浸超声自动检测系统&两个项目的研究，主要开展了超声测量、检测机器人运动学和动力学建模、误差补偿、灵敏度自动补偿和曲面构件超声检测一体化技术和轴棒类构件超声检测一体化技术的研究工作，进一步提高了复杂型面构件超声检测的效率和精度，并首次针对表面粗糙、圆柱度较差的金属轴棒类构件开发出了高效率的自动化检测设备。

Plant to 10 m tall; fruit rounded-ovoid, 2-3 mm in diam.; leaf blade ± concolor, abaxially with grayish brown pubescence, surface of blade visible between hairs under magnification, adaxially very scabrous with erect bristles.

植株给10米高；果圆形卵形体，直径的2-3毫米；叶片多少同色，背面具淡灰棕色短柔毛，在放大时毛间的叶表面可见，粗糙具直立刚毛的正面 2 T 。 tomentosa 山黄麻

Application of Laser Scanning Confocal Microscopy in Roughness Characterization of Worn Surface.

激光共聚焦显微镜在磨损表面粗糙度表征中的应用。

The new smooth surface, compact oxidation steel need to be sandblast treatment. Clean the rust completely till reach the standard of GB8923 Sa 2.5, average coarseness should be Rz=40-60 um; finally removed the dirt by constringent air.

新的光滑表面、氧化皮致密的钢板，必须喷砂处理，彻底除锈达到GB8923 SA2.5级标准；平均粗糙度RZ=40~60UM；喷砂后用清洁的压缩空气将灰尘除尽。

As he went lower, he saw that it spread among small promontoriesand inlets of rough, sharp rock, and the crisping, lapping surface showed stains斑點 of purple and darker blue.

越往下走，他发现它的四周有很多小岬和满是又尖又粗糙的岩石的水湾，被波涛拍打的易碎的表面上显出紫色和深蓝色的斑点。

It can process the material quality including copper,aluminum, iron, stainless steel, revertex, magnet etc, and can procell products' cylindricity and the surface roughness achieve 0.4μm below.

铁、不锈钢、塑胶、磁铁等；加工产品的圆柱度及表面粗糙度可达到0.4μm。希来图来样加工。我公司将以最低的价格，最优的质量。

Researched and analyzed the influence to static balance of the rotor caused by the structure of gyroscope rotor, roundness, sphericity, dimensional precision, etc. non-spherical factors and surface roughness, the change of outside environment etc., which could react directively on the natural operating and machining of the rotor.

从理论上分析研究陀螺转子本身结构，圆度、球度、尺寸精度等非球形因素以及表面粗糙度、外界环境变化等对转子静平衡的影响等，对转子正常工作及加工处理等起到指导性作用。

The epicardia l surface of the heart shows a shaggy fibrinous exudate.

心外膜表面可见粗糙的纤维蛋白渗出物。

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作：对伸臂位于顶部的单层框架—筒体模型进行分析，提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。