粗糙表面

The invention provides an insulation pad which is provided with high strength and high friction between a rail cap and a clamp, wherein the pad uses stainless steel as base, two faces of the pad are baked with enamel which is sanded and roughens the surface to brush a layer of silicon rubber, the outline is the same as the inside surface of the rail joint, the aperture on the pad and aperture distance are the same as the aperture and aperture distance of the clamp.

本发明就是制造一个钢轨端头与夹板间的高强度、高摩擦力的绝缘垫板，该垫板的由不锈钢板为基底，双面烤上搪瓷，搪瓷面先经喷砂处理，使其表面粗糙后，刷上一层的硅橡胶，轮廓与钢轨接头内侧表面相同，该垫板上的孔径与孔距与钢轨与夹板的孔径与孔距相同。

Because they have high precision and are fit for measuring soft materials, the easily scathed parts and some surfaces with some useful information.

在表面粗糙度非接触测量中，光学法是测量的主体，其测量精度高，适于对软质材料，易损工件，以及某些带有有用信息的表面进行测量。

Among the factors which have influence on scuffing failure,surface roughness and slidingspeed are very important.

在影响表面胶合失效的诸多因素中，表面粗糙度和相对滑动速度都非常重要，因此，利用改装的MHK500型环。

This body scrub eliminates dead surface skin cells, smoothes rough areas and stimulates the skin's surface.

这项全身的去角质护理，消除了皮肤表面死亡的细胞，刺激皮肤表面使皮肤粗糙区域平滑。

The microstructure, optical property, mechanical property, surface roughness, water-repellency, surface morphology are analyzed by Raman scattering spectroscopy, Fourier transforms infrared spectrometry, UV/Vis spectrophotometer, residual stress measurement, atomic force microscope, contact angle meter, optical microscope, and scanning electron microscopy, respectively.

并分别利用拉曼光谱仪、傅立叶转换红外光光谱仪、紫外/可见光光谱仪、残留应力量测系统、原子力显微镜、接触角试验、光学显微镜和扫描式电子显微镜分析与观察碳镀层的微结构、光学性质、机械性质、表面粗糙度、抗水气的能力和表面形态。

Bearing ring rotating components of the noodle and roll surface roughness is usually 1 / 10 μm, so a smooth surface of the pollutants is very sensitive to damage.

轴承环转动面和滚动元件的表面粗糙度通常为1/10 μm，如此光滑的表面对污染物造成的损坏非常敏感。

Finally, the experimental setup of MR intelligent boring bar was built on the CA6140 type lathe. The experimental results show that the method can suppress the chatter efficiently and can improve the surface quality of workpieces significantly, whose roughness has decreased from 10 μm to 1.5 μm.

最后，在车床CA6140上搭建了磁流变智能镗杆的颤振抑制实验系统，实验结果表明，变结构刚度方法能够快速高效地抑制镗削过程中产生的颤振，并且使加工表面的粗糙度Ra从10μm降至1.5μm，大幅度提高了加工表面质量。

One kind of PCD boring tool and a fine adjustment boring bar,which are suitably used in precision finishing the surface of pinhole of combustion engine piston,are introduced.

介绍了一种适用于发动机活塞销孔表面精镗加工用聚晶金刚石镗刀和可微调刀具尺寸的精密微调镗杆，该镗刀和镗杆组合具有较高的加工精度和表面粗糙度精度以及调整方便、使用寿命长的特点。

The cutting surface quality and its affecting factors of ZA22/Al〓O〓 composites were investigated systematically with hard metal alloy cutter on an engine lathe.

在普通车床上采用硬质合金刀具，首次系统研究了该复合材料的切削加工表面质量及影响因素，发现要获得低的切削加工表面粗糙度应选择小的切削深度、小的刀具进给量及高的切削速度。

The surface and cross section of uncoated and coated Polyvinyl acetals were analyzed by microscope and SEM, results showed that, the contact angle of the coated fiber decreased in most of the areas of the fibers, the chitosan film on the fibers was thin and uniform. At the same time, there was no residual material in the coating process and the whole process was environmentally friendly.

结果表明，该方法切实可行，通过显微镜和SEM照片对涂覆壳聚糖前后的维纶纤维进行微观分析，发现在化学纤维表面形成的壳聚糖膜薄而均匀，同时增加了化学纤维的表面粗糙度，涂覆效果较好；通过接触角的变化说明纤维的亲水性得到改善；该方法还具有无残留物和对环境友好的优点。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。