粗糙度

Among the factors which have influence on scuffing failure,surface roughness and slidingspeed are very important.

在影响表面胶合失效的诸多因素中，表面粗糙度和相对滑动速度都非常重要，因此，利用改装的MHK500型环。

Besides, annealing also smoothes the film surface and enhances the density and refractive index of the films.

退火处理使薄膜的表面粗糙度降低、致密度增加、折射率增大。

The surface topographies of silver oxide thin films prepared at different oxygen flow ratios have been studied by the atomic force morphology.

制备了不同氧分压比的AgOx薄膜，对其进行了原子力形貌观察，发现分压比0.4时，薄膜的粗糙度最小，均匀性也最好。

The surface topographies of silver oxide thin films prepared at different oxygen flow ratios have been studied by the atomic force morphology.

资料简介：制备了不同氧分压比的AgOx薄膜，对其进行了原子力形貌观察，发现分压比0.4时，薄膜的粗糙度最小，均匀性也最好。

Finally some reasonable truing and dressing parameters and grinding process parameters were proposed.

研究结论可用于分析和预测儿或限制工件表面粗糙度。

Due to the technology secret, there is no information aboutmeasuring the two parameters of spiral bevel and hypoid gears on line tobe vended, and the exceptional complicated teeth profile of the gearsmakes it difficult to measure the two physics parameters on line.

由于国外技术保密，目前尚无有关螺旋锥齿轮磨削力和表面粗糙度在线测量的资料公开发表，螺旋锥齿轮异常复杂的齿廓形状又给这两个物理量的实际在线测量带来困难。

The microstructure, optical property, mechanical property, surface roughness, water-repellency, surface morphology are analyzed by Raman scattering spectroscopy, Fourier transforms infrared spectrometry, UV/Vis spectrophotometer, residual stress measurement, atomic force microscope, contact angle meter, optical microscope, and scanning electron microscopy, respectively.

并分别利用拉曼光谱仪、傅立叶转换红外光光谱仪、紫外/可见光光谱仪、残留应力量测系统、原子力显微镜、接触角试验、光学显微镜和扫描式电子显微镜分析与观察碳镀层的微结构、光学性质、机械性质、表面粗糙度、抗水气的能力和表面形态。

The conception of the precision of the main parts for dry battery application and the working chart of the tolerance of the dimension and shape and the coarse degree of the surface were put for ward.

本文提出了干电池主要零配件的精度概念以及尺寸公差、形位公差、表面粗糙度等精度要求的工作图表达形式。

Bearing ring rotating components of the noodle and roll surface roughness is usually 1 / 10 μm, so a smooth surface of the pollutants is very sensitive to damage.

轴承环转动面和滚动元件的表面粗糙度通常为1/10 μm，如此光滑的表面对污染物造成的损坏非常敏感。

CAD/The CAM technology development, enables in the numerical control processing to become directly using the CAD design data possibly, specially the microcomputer and the numerical control engine bed joint, causes the design, the craft plan and the programming entire process completes completely on the computer, does not need to output the special technological document generally.

加工表面粗糙度要求低时，vF 可选择得大些。在加工过程中，vF 也可通过机床控制面板上的修调开关进行人工调整，但是最大进给速 www.3722.cn (整理。版权归原作者所有)如果您不是在 3722.cn 网站下载此资料的，不要随意相信。请访问3722，加入 3722.cn 必要时可将此文件解密度要受到设备刚度和进给系统性能等的限制。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。