类化

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Studing on samarium diiodide promoted asymmetric intramolecular reducing coupling reactions, we have made the resolution of the racemic biaryl dials by using enantiomeric N-tert-butanesulfinamine as the resolving reagent successfully and thus obtained a series of axially chiral biaryl dials with high enantiomeric excess.

中文摘要在二碘化钐促进的分子内不对称还原偶联反应中，我们不仅对联芳基二醛底物的合成路线进行了优化，还发现N-叔丁基亚磺酰胺辅基可以作为手性试剂，成功地对联芳基骨架二醛化合物进行拆分，得到高对映体过量的轴手性二醛类化合物。

In this Ph. D. dissertation, reverse microemulsion method was fully used infabricating and modifying polyacrylamide with functional and high-relative moleculeweight. The copolymerization of 2-acrylamide-2-methylpxopanesulfonic acid, fluorescent monomer 4-methoxy-N-(2-N\', N\'-dimethylamino ethyl)naphthalimide alkyl chloride quaternary ammonium salt, fluorescentmonomer 4-(N\'-methyl-1-piperazinylallyl)-N-butyl-naphthalimide chloride quaternaryammonium salt, Cationic monomer dimethylethylammonium bromide and hydrophobical monomer octadecylacrylate with acrylamide and properties of the copolymers werestudied. The interaction between five polymers and Al_2O_3(012) crystal surface have beensimulated by Materials Studio 3.0 program package, binding energies and non-bondinteraction energies and deformation energies have also been acquired.

本文以制备具有较高相对分子质量和功能型PAM为研究目的，将反相微乳液法运用到其制备及改性的有关环节，通过反相微乳液聚合工艺，将几种改性功能单体2-丙烯酰胺基-2-甲基-丙磺酸、荧光单体2-(4-甲氧基-1，8-萘二甲酰亚胺基)-乙基二甲基烯丙基氯化铵、荧光单体4-(N'-甲基-1-哌嗪基)-N-丁基-1，8-萘烯丙氯季铵盐、阳离子单体丙烯酰氧乙基-二甲基-乙基溴化铵和疏水单体丙烯酸十八酯与AM共聚，制备AMPS改性PAM、荧光示踪型PAM、阳离子单体DMB改性PAM和OA改性PAM等四类不同功能单体改性PAM，并研究其应用性能。

In chapter Ⅰ, a historial review of structure control is given; In chapter Ⅱ, A discussion of the controllability and observablity of flexible structures is given, Two kinds of controllability and observablity index are defined, and applied to actuator allocation; chapter Ⅲ considers the reduction of high order flexible structure mode; the content of chapter Ⅳ is about the basic problem of distributed parameter control system design. It is proved that a stable controllor in mode space may be unstable in real use in distributed paramater systems, also, by closed loop mode concept, a pole assignment method of flexible structure controllor design is given; chapter Ⅴ is about the low-authority controllor design, it is pointed out by use of high order eigenvalue/eigenvector perturbation, a better controllor can be designed; chapter Ⅳ considers flexible structure reduced order control; chapter Ⅶ disscusses the basic problem of flexible structure computer control, analyses discreate controllablity and observablity and its computing, the sample period and coefficient wordlength; chapter Ⅷ is on the problem of low flexibility compensation; chapter Ⅸ is a design example.

在第一章简要回顾了挠性结构控制的历史，并且指出控制中的一些问题；第二章讨论了挠性结构的能控性与能观性，定义了两类能控性程度和能观性程度指标，还将能控性程度概念应用于执行器位置的确定；第三章论述了高阶模型的降价问题，比较了适于挠性结构模型降阶的方法，指出其适用范围；第四章内容是分布参数系统设计的基本问题，首先证明在模态空间中设计的稳定的控制器在实际分布系统上可能是不稳定的，进而根据闭环模态的概念，获得挠性结构控制器设计的极点配置方法；第五章的内容是关于低权控制器的设计问题，指出利用特征值高价摄动和特征向量的摄动，可以设计出更加完善的低权控制器；第六章讨论挠性结构降阶控制问题；第七章讨论挠性结构计算机控制的基本问题，分析了时间离散化模型的能控性和能观性及其计算问题，讨论了采样周期选择和系数字长问题；第八章讨论低挠性结构的补偿问题；第九章的设计例子用来说明第二章和第四章的结果。

Ten transformants and 10 conjugons showed high-level resistance against aminoglycoside antibiotics,all of which the value of MIC＞256μg/mL carried armA gene.Conclusions:The Ab clinical isolates from burn ward in Gansu Province People\'s hospital have high drug-resistance.16S rRNA methylases gene exsist in Ab and locate in plasmid chromosome.They are easily disseminative,which demonstrated a very high level of resistance to various aminoglycosides.

甘肃省人民医院烧伤病房鲍氏不动杆菌临床分离株有非常高的耐药率，16S rRNA甲基化酶基因armA在鲍氏不动杆菌中存在，且位于质粒染色体上，易于传播和扩散，导致所有氨基糖苷类抗菌药物高水平耐药。

Triangular adjustable fuzzy number is adopted to investigate the experts' suggestions in this paper, which effectively avoids AHP's problem of consistency check. The multi-experts decision is made convergence twice by means of the cluster analysis theory. The first convergence resolves the problems of abnormal value, which reduces the electivity and subjectivity of the experts' suggestions.

本文利用三角可调模糊数调查专家意见，然后利用加权综合解模糊化方法求出权重，有效避免了层次分析法一致性检验的问题；应用聚类分析原理对群体专家决策进行两次收敛：第一次收敛解决了异常值的问题，尽可能降低了专家意见的随意性和主观性。

We researched on the prepartion of pivotal intermediate 2 and 3 for 1 P-methyl carbapenem antibiotics from intermediate 1, which is subjected to Reformastky reaction, N-alkylation, Dieckmann-type cyclisation, enolization, ester condensation etc. in sequence. The synthesis route of document is optimized by us.

我们研究了1β-甲基碳青霉烯类重要中间体的合成，从中间体1出发经Reformastky反应、水解反应合成出中间体2；经Reformastky反应、烷基化、Dieckmann环合、烯醇化、酯化合成出中间体3，并对其中各步反应作了优化和探索。

We studied DBU-mediated Ireland-Claisen rearrangement. Using DBU as the base for enolization of allylic esters of unsaturated acids 9-16, we found a novel DBU-mediated tandem Ireland-Claisen rearrangement /isomerization reactions and established a consecutive Ireland-Claisen rearrangement /Cope rearrangement.

利用DBU作为烯醇化碱，对含有活泼质子的烯酸烯丙酯类化合物9-16的Ireland-Claisen重排进行了系统的研究，创建了一条新颖的DBU-促进的Ireland-Claisen重排/异构化串联反应及Ireland-Claisen重排/Cope重排的串联反应路线。

These treatments may be used in either gender because of their lack of a feminizing estrogenic effect.

这类治疗方法可用于不同性别，因为这些制剂并无女性化雌激素作用。

What would he tell Judith and the children?

他将怎样告诉朱迪丝和孩子们呢？

I this is at that time, the opinion with peacockish true girl is full of in a heart.

这就是当时的我，一个心中布满虚荣的女孩子真实的想法。