米米

Demetrius heired a kingdom already won for him by Antigonus, the most powerful of the Successors, who, before Demetrius grew to be a man, traversed with his armies and subdued the greater part of Asia.

德米特里的父亲安提柯是亚历山大大帝死后所留下来的众多部将之中最为骁勇善战的，早在德米特里成年之前，安提柯就率领着麾下的部队横扫亚洲建立了一个庞大的国家，德米特里在父亲战死之后，自然就继承了一个现成的王国。

In this dissertation, i has used inverse microemulsions technique to synthesize nano-magnetic particles . This method made nanometer sized cages formed by dissolving surfactant molecules in an apolar organic solvent. The chemical reactions were carried out inside the cages to synthesize nanoparticles. Because the growth of the naoparticles are limited in the cages, the particles were nanometer sized particles.

论文中本人以逆微乳化法去合成磁性奈米粒子，这个方式主要是利用在非极性有机溶液当中使溶解的界面活性剂构成一个奈米级的空洞，控制化学反应在空洞中反应合成粒子，也因为粒子生成受到空洞的限制，以致生成的粒子为奈米粒子。

The Roman architects brought together the Greek and Aramaean foundations of the city and fused them into a new layout measuring approximately 1500 by 750 meters, surrounded by a city wall.

罗马建筑师将希腊人和阿拉米人的地基集中起来，规划为1500米长750米宽的区域，在外面围上城墙。

Arc de Triomphe 50 meters, 45 meters wide, 22 meters long.

凯旋门高50米，宽45米，长22米。

Arc de Triomphe in Paris about 50 meters, 45 meters wide, 22 meters thick.

巴黎凯旋门高约50米，宽约45米，厚约22米。

This is one of three arches of the Arc de Triomphe, 21 meters high, Miankuo 25.7 m, depth 7.4 meters.

这是一座三个拱门的凯旋门，高21米，面阔25.7米，进深7.4米。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

They hit all the targets set out at a distance of 100, 150 and 200 metros.

他们击中设在100米，150米和200米处的全部目标。

For example:– at 30 m distance an audible signal is given;– at 20 m distance the crane speed is decreased;– at 5 m distance the final stop signal is given.

–在30米处发出可听信号；–在20米处起重机减速；–在最后5米处发出停车信号。

Forexample:– at 30 m distance an audible signal is given;– at 20 m distance the crane speed is decreased;– at 5 m distance the final stop signal is given.

–在30米处发出可听信号；–在20米处起重机减速；–在最后5米处发出停车信号。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。