简化

Figure 1.5 is a simplified illustration of memory for a machine with a 16-bit word size.

图1.5是一个以16位（2 字节）为一个字的机器的记忆体的简化示意图。

Firstly, the Signal Noise Ratio characteristic of matched filter despread symbol and the distribution of coherent phase estimation error are derived. Secondly, the exact integration formula of BER for fading channel is presented, moreover, by using the Maclaurin series expansion of MPSK conditional Symbol Error Rate, the simplified BER approximations for BPSK and QPSK are derived over AWGN, Nakagami-m fading and Rayleigh fading channel.

首先推导了匹配滤波解扩符号的信噪比特性和相干相位估计误差的分布；然后给出了衰落信道中误比特率的精确积分式，并利用MPSK条件误符号率的麦克劳林级数形式，推导了AWGN，Nakagami-m衰落和瑞利衰落信道中BPSK，QPSK误比特率的简化逼近式。

Macr os to simplify this task will be defined.

将定义一些宏来简化这样的工作。

Firstly, this paper introduce the present and prospective development, moreover compared advantage and short of different roll forming theory. Subsequently simplified process and analyzable model of channel section according to deforming elastic-plastic macro deforming finite element theory.

本文首先介绍了国内外关于辊式冷弯成型理论研究的现状与发展趋势，并比较了各成型理论的优缺点，随后在分析槽钢辊弯成型特点及其变形规律的基础上，以弹塑性大变形有限元理论为基础，对槽钢成型过程做出合理简化，建立分析模型，利用MARC软件对槽钢辊弯成型进行了三维有限元数值模拟分析。

This paper simplified process of spinning head according to elastic-plastic macro deforming finite element theory. The FEM software MARC is used to simulate the forming processing of thick wall head in drffereut teixiperature conditions in warm spinning.

文中，以弹塑性大变形有限元理论为基础，对封头温旋压成形过程做出合理简化，建立分析模型，利用非线性有限元分析软件MARC对不同温度状态下的厚壁封头温旋压成形过程进行了数值模拟。

Programming with customer macro instruction is a kind of advanced programming method which is offered by FANUC CNC system,which programming with the replacing function code or address in programs by variable .

用户宏指令编程是FANUC系统所提供的一种先进的编程方法，它使用变量代替程序中的功能代码或地址值进行编程，使数控程序具有通用性和灵活性并简化了数控编程。

Microsoft's latest macro programming language is simple to use, powerful, and not limited to Word documents.

Microsoft程序设计语言给简单的最新的宏指令的时候这样非常的程序的范围内简化反复的作业，不被制限在文档。

Programming with customer macroinstruction is a kind of the advanced programming method,which is offered by FANUC CNC system,The function code or address can be replaced by variable during the programming.

用户宏指令编程是FANUC系统所提供的一种先进的编程方法[1]，使用变量代替程序中的功能代码或地址值进行编程，使数控程序具有通用性和灵活性，且简化数控编程，是数控技术的重要组成部分。

It has been put forward and established the macroscopical simplified model.

3提出并建立了筒体结构的宏观简化模型。

The research results have shown that the configuration of the magnetic bearing reduces overall system size, and has high efficiency. The axial and radial suspension forces have great linearity. The symmetrical characteristic strenuously, and movement of every degree of freedom around balanceable position has no coupling and the control flux of every degree of freedom is independent. It is beneficial to simplify and design the controller and the circuit power amplifier. The magnetic bearings operate stably with decentralized PID controllers.

研究结果表明：这种磁轴承结构合理紧凑，效率高；磁轴承轴向、径向悬浮力具有较好的线性和对称性，有利于控制器及功放电路的简化与设计，并获得良好的拉制性能；各自由度运动和磁路几乎没有耦合，采用分散独立的PID控制器实现了磁轴承的稳定工作。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。