筛分析

Calculating the pavement fragment adoptioning contradicting -cleft -glue and glass fiber grille ,deal with the existing crevasse, at kaminaka surface layer install rubber asphalt water proof adhesive layer , at the same time guarding against water coming into nakashita surface layer、enhanced interlamination bonding ...

论文进行橡胶沥青混合料的主要试验内容有：1、根据京秦高速公路管理处提供的石料进行目标配比设计；2、进行混合料马歇尔击实及相关性能试验确定最佳油石比。3、根据冷料配比进行热料仓筛分，确定热料仓配比；4、根据热料仓配比进行马歇尔击实试验。4、进行混合料的路用性能试验，分析橡胶粉的掺入对沥青的高低温性能、弹性性能、抗老化性能的改善情况，分析橡胶粉的掺量、目数、胶源、加工工艺和基质沥青对橡胶沥青性能改善的影响程度。

Small size, short life cycle, self-pollination, and high seed number, andfavorable genetic traits such as self-fertilization, a small genome, efficienttransformation, and mutagenesis.

本文采用RAPD 技术分析了盐芥居群的遗传多样性，从400 余个随机引物中筛选出了23 个扩增性强、重复性好、带型明显、多态性高的引物对盐芥居群进行分析。

The practical problems in the granulometric analysis method—the water sedimentation analysis method and the dry sieve analysis method,are analyzed,and an improved water sieve analysis method is developed in this paper.

文章分析了目前粘性土颗粒分析的主要方法——静水沉降法和干筛法，指出其存在的问题。

Cause and basis for reforming the middle pressure s hi ft saturation column were analyzed,working principle of the new type of vertic al sieve plate column and its reforming situation in the middle pressure shift s aturation column were discussed,analysis and contrast were made for the operat ing parameters and economic benefit before and after reformation.

分析了中压变换饱和塔改造的原因和依据，论述了新型垂直筛板塔的工作原理及其在中压变换饱和塔的应用改造情况，对改造前后运行参数和经济效益进行了分析对比。

The aerodynamic characteristics of the cuted tip rhombus wing and double-delta wing of middling sweepback angle and aspect ratio about sixty type are investigated by a numerical method based on Eular equations.

采用Euler数值计算方法，对60多种中等后掠角及展弦比的切尖菱形机翼、双三角机翼纵向气动力特性进行了计算、分析和比较，从中筛选出16种切尖菱形机翼、14种双三角机翼进行了全机高速风洞实验研究，给出了机翼的展弦比、前缘后掠角、根梢比及几何扭转变化对全机升力、阻力及俯仰力矩的影响曲线和数据分析，在此基础上提出了用于定量估算两类机翼纵向气动力特性的关系式及修正因子。

Computer was used to analyze the possible secondary cleavage sites on HPV11 E2 mRNA and to predict the secondary structures of substrate and ribozymes. According to the theory of Symons headhammer ribozyme, there are 32 sites to targetting sequences.

遵循Symons锤头状核酶结构和GUX剪切位点原则，靶序列存在32个剪切位点，通过计算机软件分析核酶的最佳剪切位点，并对底物及核酶的二级结构进行预测及进行相应基因生物学功能和基因同源性分析，筛选出2个锤头结构核酶。

Fingerprints of broiler chickens divergently selected for very low den sity lipoprotein in fat line and lean line of the third generation were studied using inter simple sequence repeated technique. Geneti c polymorphism and genetic similarity coefficient between two groups were analyze d. Ten primers were screened from 60 SSR primers and 62 sites were deprived. Of which 39 bands were polymorphic sites and the frequency was 63 percent.

通过对初步进行血浆极低密度脂蛋白双向选择的三世代高、低脂群肉鸡进行ISSR指纹分析，评定其遗传多态性及两群体间的遗传相似系数。60个引物筛选出10个引物用于检测分析；共扩增出62条谱带，其中39个是多态性片段，多态率为63%。

Final diagnoses for the prospective cases based on combined morphology and ancillary testing were 24 CHMs (including 7 eCHMs), 7 PHMs, and 11 nonmolar specimens.

有了分析这些前瞻病例的经验之后，我们改进了分析方法，即联合p57免疫染色和形态学来筛分病例进行分子基因型检测。

Two electrolytic manganese slags are investigated using XRD, DSC, chemical analysis and screening.

采用X射线衍射、DSC、化学分析和筛分等手段对2种来源的电解锰渣的基本性能进行了分析。

On the base of model machine and productive practice, analyses the operating principle, main performance, characteristic of vacuum density separator as well as relations between parameters. develops the kinetic condition and rule of grain and stone on the screen, discusses the effect of air velocity in course of stone removal, and makes some amendment to the textbook［1］, gives some experience and method about the design of the mechanism.

在样机和大量生产实践的基础上分析了比重去石机的工作原理、主要性能、特点及各参数之间的关系，分别阐述了石子和谷粒在去石筛面上的运动条件和规律，分析了气流速度对去石效果的影响，并对教科书存在的问题进行了修正和补充，得出了一些有关机构设计方面的经验和方法。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐