等轴的

V belt driving device developed is superior to flexible plate coupling and roller chain driving in VNH behavior, working endurance and axial and lateral offset tolerance.

所开发的三角带传动装置在振动噪声性能、作寿命和对轴向以及径向偏心的容忍度等方面都优于常用的柔性板式联轴器和高速滚子链传动装置。

Aiming at the mathematic model of shafting crankle coupling vibration based on the subsection continuous mass model,the multidimensional frequeney analysis method is put forward and developed.Combining frequency change with shafting configuration parameter,it's more favorable to have direct analysis.The method...

针对基于分段连续质量模型的轴系弯扭耦合振动数学模型，进一步简化并提出多维频率分析方法，将频率变化与轴系的结构参数联系起来，有利于直观分析，同时给出分析振型、共振频率及共振模态等的方法

With the competent germinating epicotyl of cotton as receptor in exogenous gene transformation, NPTII (neomycin phosphotransferase Ⅱ) gene carrying selection marker and GFP reporter gene were mediated into cotton by agrobacterium-mediated transformation. The pre-culture time, bacterial-immersing time, co-culture time and antibiotics concn., etc of using agrobacterium-mediated transformation in the transformation of competent germinating epicotyl of cotton were studied.

方法］以棉花感受态萌动的上胚轴作为外源基因转化的受体，用农杆菌介导法将携带有筛选标记NPTII基因及GFP报告基因导入棉花，研究了农杆菌介导法用于棉花感受态萌动上胚轴转化的预培养时间，浸菌时间，共培养时间及抗生素处理浓度等。

MethodWiththe competent germinating epicotyl of cotton as receptor in exogenous gene transformation,NPTIIgene carrying selection marker and GFPreporter gene were mediated into cotton by agrobacterium-mediated transformation.The pre-culture time,bacterial-i mmersing ti me,co-culture ti me and antibiotics concn.,etc of using agrobacterium-mediated transformationinthe transformation of competent germinating epicotyl of cotton were studied.

方法以棉花感受态萌动的上胚轴作为外源基因转化的受体，用农杆菌介导法将携带有筛选标记NPTII基因及GFP报告基因导入棉花，研究了农杆菌介导法用于棉花感受态萌动上胚轴转化的预培养时间，浸菌时间，共培养时间及抗生素处理浓度等。

Based on rubbing model of a two-disk rotor-stator system with consideration of both rotor and stator dynamics,a numerical integration program is applied to numerical simulation and analysis of the nonlinear dynamics of this system,such as bifurcation,Poincare section map,trajectory of axes,phase trajectory,frequency spectrum diagram and time response.

基于一新型径向-轴向复合碰摩双盘转子-机匣力学模型，利用数值积分和Poincare映射方法，对转子-机匣系统由于径向-轴向碰摩故障导致的非线性动力学行为进行了数值仿真研究，给出了系统响应随转速和偏心量变化的分岔图和一些典型的Poincare截面图、相轨图、轴心轨迹、幅值谱图和时域响应等。

This thesis contains three parts: The first part focused on the simulation of the dynamic buckling for rod impacted by dynamic force and rigid body in axial direction, which is hinge joint and uniform cross section, basing on the ANSYS/LS-DYNA and PAMCRASH.

本文的研究工作主要有三部分组成：第一部分基于有限元程序ANSYS/LS-DYNA、PAMCRASH分别对两端铰接、等截面直杆在轴向动力载荷作用下的屈曲和刚性块轴向冲击作用下直杆的动力屈曲过程进行了数值模拟和分析。

In the fin219-null mutant background, GUS staining can be detected in the hydathode of cotyledons, and the guard cells around hydathodes. GUS staining are also found in the base of trichomes, hypocotyls and roots. In contrast, in the phyA mutant background, GUS-FIN219 was not expressed in the hypocotyls.

结果发现转殖在fin219-null突变株背景下，FIN219会特别表现在植株叶缘出水孔与附近的保卫细胞及毛茸基部、初生叶、下胚轴、根部等处，然而在phyA缺失的时候植株幼苗的FIN219则不会在下胚轴表现。

The axes of length to diameter ratio bigger than 20 is called the thin major axis .

长径比大于20的轴称为细长轴，由于刚性很差，在加工中产生的切削力、切削热、振动等因素将直接影响工件加工的尺寸精度和形位精度，加工难度大。

A quick DNA extraction technique which was fitting for maize variety identification and establishing DNA fingerprinting pool was explored ,and the technique was well applied in the following tissues for DNA extraction : embryo, endosperm; radicel, coleoptile , hypocotyl from germinated 1～3 days material .

本实验探索了适用于玉米品种鉴定及DNA指纹库构建的玉米品种DNA快速煮沸法，用快速煮沸法提取了玉米种子胚、胚乳；水培初生根、侧根；种子出苗后的初生根、侧根、胚芽鞘、胚轴、叶片等组织DNA，结果表明，种子胚、胚乳组织；水培2～4d水培初生根、侧根组织；出苗1～5d的胚芽鞘、胚轴组织用快速煮沸法提取DNA效果较好。

Multi-Axis interpolation NC program simulation system was constructed by compiling virtual machine,virtual machine controller,virtual stock,virtual tool,virtual coordinate and virtual clips.Contrasting experiments between virtual and real cutting process were carried out and Muti-axis interpolation cutting simulation based on NC code was achieved.

通过建立虚拟机床、虚拟机床控制器、虚拟毛坯、虚拟刀具、坐标系以及虚拟夹具等，建立了多轴数控程序仿真环境，实现了基于NC代码的多轴联动切削过程的几何仿真，并通过切削对比试验验证了该仿真系统的可行性。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。