等轴的
- 与 等轴的 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
One (1) pumps Products: submersible pump, jet pump, drainage pump, sewage pumps for civilian use; end suction pumps, in the open pumps, booster pumps, fire pumps for industrial and commercial; centrifugal pump, diaphragm pump, column Cypriot pump applicable to agriculture; desalination pump, reciprocating pump, axial flow pump for municipal construction; bilge pumps, cooling pumps, sewage pumps, high pressure washing pump, water pump for sea; purification and filtration equipment: FLECK valves for the boiler water softener system, reverse osmosis pretreatment system installations, domestic and commercial water softener system; STRUCTURAL cans resin applied to sand filters, commercial water softener, ion exchange, multi-media filtration, activated carbon filtration; CODELINE Hymenolepis apply to sea water, bitter, salt water desalination projects, power plant boiler supply water treatment industry, chemical industry process water, electronics, semiconductor industry, ultrapure water treatment, metallurgy, light industry, electroplating industry wastewater treatment, food and beverage, health care; swimming pools and water features equipment for spa, swimming pools, large baths and so on.
其中泵类产品:潜水泵、喷射泵、排水泵、污水泵适用于民用;端吸泵、中开泵、增压泵、消防泵适用于工业和商用;离心泵、隔膜泵、柱塞泵适用于农业;脱盐泵、往复泵、轴流泵适用于市政建设;舱底泵、冷却泵、污水泵、高压冲洗泵、饮用水泵适用于海运;净化与过滤设备:FLECK阀门适用于锅炉软水系统、反渗透系统的预处理装置、家用及商用软水系统;STRUCTURAL树脂罐适用于砂滤、商用软水器、离子交换、多介质过滤、活性碳过滤;CODELINE膜壳适用于海水、苦、咸水淡化工程、电厂锅炉补给水工业处理、化工行业工艺用水、电子、半导体行业的超纯水处理、冶金、轻工业、电镀等行业的废水处理、食品饮料、卫生医疗;泳池及水景设备适用于水疗、游泳池、大型浴场等等。
-
The globularization of lamellar α increases with increasing strain and strain rate, and decreases with increasing heating temperature.
等轴化的程度随变形程度、应变速率的增加而增大,随变形温度的提高而减小。
-
The microstructures and second phases were examined by transmission electron microscopy.It is found that the specimen treated by 500 ℃/100 h has the best corrosion resistance among all the specimens.TEM analysis of the specimens tempered at 500 ℃ with different time shows that the second phase changes from the seriate strips to the banding...
用透射电镜研究了这些样品的显微组织和第二相,观测到随着保温时间延长,500℃下保温样品中的第二相由连续片层逐渐转变成带状分布的颗粒,保温时间达到100 h时,基体内析出βNb.560℃下保温样品与500℃下保温样品有相似的组织转变过程,只是时间大幅缩短,保温仅10 h时,基体已完全再结晶为等轴晶。
-
The results show that the microstructure of the cladding wire by drawing at room temperature is vimineous grain as fibril shape from prime equiaxed grain. The fibril diameter is in inverse proportion to deformation and the fibril length is in direct proportion to the square of deformation approximately. The ultimate tensile strength of the cladding wire by drawing at room temperature goes up in direct proportion to square root of deformation, whereas the elongation decreases and fluctuates.
结果表明:显微组织自原始的等轴晶变为细长条纤维状,纤维直径与形变量近似地成反比,纤维长度与形变量的平方近似地成正比;经室温拉变形的铜包铝线的极限抗拉强度随形变量增大而增大,与形变量平方根呈直线关系;延伸率随形变量增大逐渐降低,但延伸率波动较大。
-
The L2 glass with 30 mass% Al2O3 filler (L30A) can be fully densified at 800oC in 1 h and devitrified at 850oC for 10 min. The sintering scheme has been optimized to achieve limit dissolution of Al2O3 grain and crystallization of equi-axial LaBO3 and flaky LaAl2B3O9 crystals. The final matrix has limited glassy phase.
L2玻璃添加30 mass%的氧化铝(简称L30A)於800oC持温一小时并於850oC作十分钟的结晶处理可达完全致密,整体的烧结流程设计亦已最佳化,微结构观察中可发现等轴LaBO3及片状LaAl2B3O9之结晶体,其烧结后之基地仅残存有限的玻璃相。
-
Molar-tooth structures refer to the aggregations of equal-axised or polygonal microspar calcite with a crystal size of 0.01mm and a clear boundary, which are mainly developed in the Precambrian fine-grained carbonate rocks. The morphology of Molar-tooth can be divided into ribboned, nodular and clastic forms.
臼齿构造是特指那些发育在前寒武纪细粒碳酸盐岩中有清晰边界、粒度在0.01mm左右的由等轴或多边形的微亮晶方解石组成的集合体,其形态可分为条带状构造、瘤状构造及棱角碎块状构造。
-
When designing and selecting this connection, it is necessary tocalculate shafts' strength.
在等距型面联接的设计或选用过程中,轴的强度验算是十分必要的。
-
It has validated the system of high efficiency, safety, and stable quality. Zero- programming method can be used in NC process with fixed and limited parameters, such as gear grinding, gear shaper, and manufacturing of axis and disc parts.
零编程方法适用于编程参数和工艺参数固定、有限的数控加工,还可推广于齿轮加工的磨齿、插齿,以及轴类、盘类等零件的加工。
-
Based on the processed accessory, the number, the position and the machining data of the holes and the form of the principal axis are determined; The driving way of the headstocks are drawn, the power is transmits by the methods of optimization, the driving parameter are determined, the structure of the principal axis are designed and the strength of the parts, such as the gears and the bears, are checked.
根据被加工零件确定加工孔的数量、位置、切削用量及主轴类型,拟订了主轴箱的传动方式,应用最优化方法传递功率,削减振动,确定传动参数,设计轴的结构,进行如齿轮、轴承等相关零件的强度校核计算。
-
The results show that, the coefficients of welded joints are both greater than 0.9, but the yield strength of weld joint filled with Al-Mg-Zr-Sc welding wire is greater 100 MPa than that of filled with Al-Mg-Zr welding wire. It indicates that the Al-Mg-Zr-Sc welding wire is the best alteration of filling materials to weld of Al-Mg-Sc alloy.
但采用Al-Mg-Zr-Sc合金焊丝为填充材料时,焊缝晶粒组织明显细化,熔合区形成的细小等轴晶层提高了基材与焊缝填充材料的结合力,焊接接头的屈服强度比采用Al-Mg-Zr合金焊丝为填充材料时提高了100 MPa,显著提高了Al-Mg-Sc合金焊接构件的许用强度,因此焊接Al-Mg-Sc板材更宜采用Al-Mg-Sc-Zr焊丝。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。