等轴
- 与 等轴 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
First according to the hydraulic pressure elevator system diagram, use the machine design and hydraulic transmission knowledge calculates the diameter of the plunger, cylinder tube wall thickness as well as cylinder bottom thickness; second, through the examination confirmation to the obtained result to complete the work of cylinder design; Simultaneously has carried on the component choice and the computation; Through to the system calorific capacity computation the and the volume of cooling water while the fuel tank cools when needs to complete the hydraulic pressure elevator fuel tank design; Based on the system oil stream condition to calculated the tube internal pressure lose, the local pressure loss as well as the all of the pressure lose to carried on the system checking calculation; Finally through the consult correlation design handbook to calculation and examines the belt, the band pulley, the axis, as well as the key, has completed the hydraulic pressure elevator pumping station transmission system design.
首先根据液压电梯系统原理图,利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度,并对所得结果进行校核验证完成了工作油缸的设计;同时进行了元件的选择和计算;其次,通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计;依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算;最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核,完成了液压电梯的泵站传动系统的设计。
-
Firstaccording to the hydraulic pressure elevator system diagram, usethe machine design and hydraulic transmission knowledge calculatesthe diameter of the plunger, cylinder tube wall thickness as wellas cylinder bottom thickness; second, through the examinationconfirmation to the obtained result to complete the work ofcylinder design; Simultaneously has carried on the component choiceand the computation; Through to the system calorific capacitycomputation the and the volume of cooling water while the fuel tankcools when needs to complete the hydraulic pressure elevator fueltank design; Based on the system oil stream condition to calculatedthe tube internal pressure lose, the local pressure loss as well asthe all ofthe pressure lose to carried on the system checking calculation;Finally through the consult correlation design handbook tocalculation and examines the belt, the band pulley, the axis, aswell as the key, has completed the hydraulic pressure elevatorpumping station transmission system design.
首先根据液压电梯系统原理图,利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度,并对所得结果进行校核验证完成了工作油缸的设计;同时进行了元件的选择和计算;其次,通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计;依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算;最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核,完成了液压电梯的泵站传动系统的设计。
-
The failure characteristics of large pump units are that the influence is great, the reasons are complicated, it is difficult to observe and the failure rate is hard to determine. The main failures of large pump units are as follows: burn out of thrust bearing liner of the motor, failure of stator and rotor coil insulation of the motor, wear-and-tear of guiding bearing and shaft neck of the pump, breakdown of adjusting mechanism of the pump blade, and pump cavitation. The reasons of main failures are studied in design, structures, installation and operation etc.
分析了大型水泵机组故障的特点:影响大、原因复杂、隐蔽性强和故障率确定难;确定了主要故障形式:电机推力瓦烧损,电机线圈绝缘失效,水泵导轴承及轴颈磨损,叶片调节机构失效,水泵汽蚀;从设计、结构、安装和运行等方面研究了主要故障的原因。
-
AFTER THE OWNERSHIP TRANSFER,IN ORDER TO STRENGHTEN THE MANUFACTURING CAPABILITY,THE COMPANY PURCHASED MANY NEW EQUIPMENTS LAST YEAR,THERE ARE CNC LINE CUTTING MACHINE,CNC STATOR COIL WINDING MACHING,CNC SPOT WELDING MACHINE,BELT SAW CUTTING MAHCING,HEATTREATMENT MODIFIED EQUIPMENT,500T FUEL PRESSER,CNC LATHE,STATOR AND ROTATOR LIQUER IMMERSION AND DRYING PRODUCTION LINE,SINGLE BOLT PRESSER,ARMATURE PRODUCTION LINE,STARTER ASSEMBLY AND TESTING LINE,LIQUER SPRAY PRODUCTION LINE,GERMANY TOX COMPANY PUNCHING AND CONNECTING FACILITY AND GERMANY NUT FASTENING FACILITY,AND WE ALSO PURCHASE THOSE ADVANCED TESTING FACILITIES SUCH AS THE DOMESTIC MOST ADVANCED COMPREHENSIVE TESTING UNIT,THREE DIRECTION HIGH AND LOW TEMPERATURE CHANGE AND VIBRATION TESTING UNIT,HIGH TEMPERATURE TESTING BOX.
企业转制后,为提高产品制造能力已购置生产设备:数控线切割、数控定子绕线机、数控点焊机、带锯床、热处理调质设备、500吨油压机、数控机床、定子、转子浸漆干燥线、单螺杆空压机、电枢生产线、起动机总装及试验线、喷漆线、德国TOX公司冲压连接设备和德国的螺栓紧固设备。试验设备:购置目前国内最先进的起动机综合试验台、三轴向高低温交变振动试验台、高温试验箱等试验设备。
-
The pattern of the tyre of agricultural vehicles has to fit in with the inclement working situations of the vehicles,which brings some difficulty to the pattern block mold design of the tyre.
文章介绍了农用轮胎的特点和轮胎模具的生产流程,然后结合轮胎花纹块的铸造、抛光、机械加工等工艺要求,阐述了农用轮胎花纹块模具设计方法并导出计算公式,内容包括:径向断面的工艺尺寸设计、轴向与周向的展开与弯曲设计;提出采用Coons曲面构造出模具内腔壁曲面的方法。
-
This article first has carried on the introduction to the design proposal; And introduced the electric motor choice method, the box body design, the axis design, the gear design, the key choice and so on, then introduced briefly the reduction gear assembles some correlation knowledge and technical order; Finally has listed in the design process glances through and has referred the literature.
本文首先对设计方案进行了介绍;并介绍了电动机的选择方法、箱体的设计、轴的设计、齿轮的设计、键的选择等,然后简要介绍了减速器装配的一些相关知识及技术说明;最后列出了设计过程中翻阅及参考过的文献。
-
The Company may, in accordance with the requirements of the processing parts and design and manufacture of various types of special combination of automated machine tools and automatic lathes, precision-gear automatic tapping machines, reciprocating dedicated machines, fixed multi-axis drilling tapping machines, elevating drilling Tapping dedicated machines, multi-disc special machines, machine tools and various combinations for accessories, dynamic head, boring Xitou and hydraulic slider, at the same time various types of automated machine tools for transformation, maintenance, repair and upgrading.
本公司可根据客户的零件和加工要求来设计制造各类自动化专用组合机床及自动车床,齿轮式精密自动攻牙机,往复式专用机,固定式多轴钻孔攻牙机,升降式钻孔攻牙专用机,多工位圆盘式专用机,以及各类专用组合机床配件;动力头,镗铣头和油压滑台等,同时对各类自动化专用机床改造,保养,维修,升级。
-
Transmission by the spindle, water-cooled bearing box, coupling, etc.; spindle made from high quality steel.
传动组由主轴、水冷轴承箱、联轴器等组成;主轴由优质钢制成。
-
Instant noodles and rice Industries: Stainless Steel Net steamed chain, all kinds of oil boxes, hanging drying box, noodle cutter, noodle Salisbury, Fulcrum, molding boxes.
方便面及米粉行业:蒸熟不锈钢网链,各种油盒、烘干吊盒、面刀、面梳、支轴、成型盒等。
-
Lo models with a horizontal mixer, biaxial pulp of the mixer, Central touch granulators, [250, 320, 350], water droplets grinder, mixer drum additives,(SR-enrichment Material equipment), bucket elevator, U-cutter-type carrier, there are die-pellet feed and other 30 kinds of ancillary equipment.
机型有卧式螺带混合机、双轴浆叶混合机、环摸制粒机、[有250型、320型、350型]、水滴粉碎机、鼓式添加剂混合机、、斗式提升机、U型输送绞龙、还有平模制粒机等30多种饲料配套设备。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。