等加速度

The influence of excess anhydrous hydrogen fluoride, the amount of oleum and its trickling rate, the time...

在此过程中，本文研究了无水氟化氢过量百分率、发烟硫酸用量及滴加速度、六氟磷酸的加热时间、加热温度以及冷凝介质等因素对五氟化磷产率和纯度的影响。

The influence of excess anhydrous hydrogen fluoride, the amount of oleum and its trickling rate, the time and temperature of heating hexafluorophosphoric acid, and refrigerants on the yield and the content of phosphorus pentafluoride was studied.

在此过程中，本文研究了无水氟化氢过量百分率、发烟硫酸用量及滴加速度、六氟磷酸的加热时间、加热温度以及冷凝介质等因素对五氟化磷产率和纯度的影响。

The method combines the inverse dynamics control with the ZMP-plane acceleration projection, whereby the whole body stability of the robot can be considered simultaneously when tracking the predefined trajectories. With this method, the inapplicability existing in the classical control methods in the terms of disturbance rejection and stability maintenance is solved.4 Finally, in order to verify the proposed methods, experiment platforms for the motion planning and disturbance rejection control are constructed respectively.

提出了利用逆动力学控制和ZMP平面的加速度映射相结合的抗干扰策略，在对运动轨迹进行精确跟踪的同时保证系统整体的动态平衡性，解决了经典轨迹跟踪控制方法在抗干扰及稳定性保持等方面的不足。4为验证本文所提出方法的有效性，分别构建了非规则运动规划与抗干扰控制算法的实验平台，详细地介绍了运动生成和运动执行系统的设计与构成。

A slim azimuth 20 independent-arm caliper logging tool;2. Design of TFY-1 universal azimuth jointer with a restrained gyroscope;3. The pit shaft parameters of the elevation angle,the azimuth angle,the tool of facial angle and so on are obtained after the computation.

陀螺测斜技术以动力调谐速率，陀螺测量地球自转角速率分量和石英加速计测量地球加速度分量为基础，经计算得出井筒的倾斜角、方位角、工具面角等参数。

The displacement,velocity and acceleration of linear motor could be measure simultaneously by this system,and the transient response time could also be determined.

系统能够同时测量并绘制出超声电机运行过程中的位移、速度和加速度曲线，方便确定其响应时间，且具有实现简单、操作方便、易于扩展等特点。

Newton's second law formula: F = ma (F is force, m is mass, a for acceleration) and so on.

牛顿第二定律计算公式：F=ma（F为合力，m为质量，a为加速度）等。

First, using UG software create the diorama of sample and transform data style into STL; second, transfer the data of diorama from UG to HRP-Ⅲ RP machine, which should set some parameter with parenthetic expert slicing software; finally, surface treatment spray trailor-made paint.

其基本的工艺流程：首先用UG软件建立样件的立体模型，并转换为STL数据格式，再传输立体模型数据到HRP-Ⅲ快速成型机（武汉滨湖机电技术产业有限公司生产）上，通过其配带的专用切片软件设置激光能量大小、激光头的速度及加速度等参数将模型成型。

The results of computations show that the structure of unsteady flow is complex during both the acceleration phase and the constant velocity phase.

计算结果表明启动过程绕大攻角翼型的加速流动结构复杂，该瞬态过程的流动分离现象也明显区别于稳态过程自生和自维持的分离流动，并且启动加速度大小对流动的分离、漩涡结构和强度等都有直接影响。

The QVBA key micro-machined technology are also developed in this paper, such as: single step double sides multilayer photolithographic process, quartz crystal anisotropic etching process.

在仿真分析基础上，完成了石英振梁加速度计的设计及关键微加工工艺研究，包括：单步双面多层光刻工艺、石英晶体各向异性刻蚀工艺等。

According to the definite relation of seismic motion weaken and the earthquake belt, seismicity parameter of the latent epicenter area, we applied the probability method to calculate the peak acceleration of bedrock in level of different probability level for field site.

利用地震危险性概率分析方法对大型一等工程－某大型水利枢纽工程所在的场址进行地震危险性分析；该拟建工程场址所在的西昆仑地震带是新疆境内地震活动强度最高、频度最大的地震带，拟建工程坝高库大，为了进行准确的地震危险性分析研究，本研究根据区域地震活动性及地震构造研究成果，确定了地震活动性参数，按照构造类比、历史地震重演原则划分了潜在震源区；在分析了区域地震活动环境和地震构造等因素后，综合评价其对场地地震危险性的影响；根据确定的地震动衰减关系及地震带、潜在震源区的地震活动性参数，应用概率方法计算得出了场地不同概率水平的水平向基岩峰值加速度。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。