窑

The kiln body is divided into two sections of electrical furnace body and dynamic rotation with the kiln body constructed of clayed circular hearth uniformly inserted with 9 silicon carbon rods along the circular axis( one group made up of 3 rods and Y connection for every 3 groups).

窑体部分又分为电炉炉体和动力转动两部分，炉体部分采用粘土质圆形炉膛，沿圆轴向均匀插9根硅碳棒（每三根串联成一组，三组按& Y &接线）高铝质的陶瓷炉管又置于硅碳棒内周，通电后硅碳棒产生高温，加热炉管。

Contact model was established to quantitatively calculate the preparation of cement with different clinkers of varying strength by means of mathematical modeling of blending materials. Reactivity of clinkers from varying kiln system can be assessed by this model to produce cement.

采用混杂材料的数学模拟理论，建立了可以定量计算不同强度的熟料混合磨制水泥的接触点模型，应用该模型方法可以比较不同窑型熟料混合粉磨制备水泥时掺加熟料的活性效应。

This paper targets at the design of a new dry process kiln cement grinding plant, whose production capacity is 2500 tons of cement clinkers per day. According to some relative references and the product quantity required per day, we design and calculate the cement burden plan, the three great balances (which include material balance, main engine balance and storehouse balance) and the choice of the type of equipments used in the cement grinding plant.

本论文就2500 t/d（日产2500吨）熟料新型干法窑水泥粉磨车间进行设计，根据相关文献以及对产量要求对水泥的配料方案、三大平衡（物料平衡、主机平衡、储库平衡）和水泥粉磨车间系统设备的选型进行设计与计算，并据此对水泥粉磨车间的主要粉磨设备以及其相关的附属设备的型号进行了选择。

Through adjusting the ratio of raw materials and fuel, materials with three ratios were ground with an OK12-2 raw mill (Φ1.2m). After being roasted in a shaft kiln (Φ2.8×10m), clinkers have been obtained.

通过工业试验调整原料与燃料材料的配比，在OK12-2立磨上(磨盘直径Φ1.2m)磨制出不同三率值的生料，然后在Φ2.8×10m的立窑上进行煅烧。

This article provides a preliminary analysis and comparison of several pieces which are comparatively well preserved and fairly dateable, and attempts to determine the routes along which they were imported, the kilns where they fired, and their exact dating.

本文对其中保存较完整、时代较明确的几件器物进行了初步地分析和比较，并试图探讨这些器物的输入途径、烧制窑口、年代等问题。

These people have no association with us whatsoever. Most of them don't even have a factory, and the so-called "Italian vacuum driers" they have been trying to copy are nothing like ours. None of them meets our standards and none has the all important controller technology which is essential to the success of our vacuum drying.

这些人和我们一点关连都没有，而他们所称制造的&意大利真空乾燥窑&更是无法与我们的相比---因为很多这些人工厂里工人都没有的，不只达不到我们的质量标准，更重要的是他们的产品都缺乏了我们的电脑控制系统，而这个电脑控制系统及它配置的乾燥程序才是我们真空乾燥科技的精髓！

As pointed out by Kamei (1975), bowls and plates are the most frequently-occurring Yue items at Japanese sites along with such vessels as ewers, jars, boxes, spittoons and cup stands.

大部分产于上林湖窑址，在一些东南亚地区、印度洋、红海，越窑瓷器通常与长沙的瓷器同时发现。

Its production methods are: Dredging mud to folder Bunang Sheng, put the water's fine who clarified to clean water, so slightly dry, into the Yellow Lead (with different pigment additives), group search, such as face, into the mold, remove the dried, carved molding, then rice bran and yellow cow dung and firing into the kiln, then wax dye ink, then the storage of steamed rice vinegar to serve.

其制作方法为：挖河泥以夹布囊盛之，水中摆之的细者，澄去清水，令微干，入黄丹，团搜如面，入模中，取出阴干后，雕琢成型，再以稻糠并黄牛粪和入窑中烧制，而后染墨上蜡，再用其贮米醋蒸之，即成。

The fan assembly is roof mounted, providing a vertical airflow pattern and uniform temperature throughout the chamber.

这种风扇装于窑顶，提供了垂直的气流并能使整个炉腔温度保持均匀。

By mechanical analyzing the shaft of supporting wheel, the relation between the axis line and fatigue fate of support system is derived.

本文通过对回转窑托轮轴进行力学分析，导出支承系统各托轮轴疲劳损伤与轴线偏差的关系，从而根据轴线检测得出各托轮轴剩余疲劳寿命；以轴线偏差调整量为优化变量，各托轮轴中最小的剩余寿命最大为目标函数建立优化模型，结合现场实例进行支承系统等寿命优化调整研究。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。