磨损

I'll wait until he gets worn day, beats some guys up along the way, then I can kick it into high gear while everyone else is dead-tired.

我将等候直到他拿磨损的日子，向前搅拌一些家伙方式，当其他人死的时候，然后我能踢它进高速档之内-疲累的。

We all know that roller, block between hobber and hobber for the imprint, but the artificial division between rolling roller, block roller and embossing roll is a compact, linear three-roll and is consistent, so when the pressure is too large, due to the printing plate is compressed with the roller between a certain amount of sliding friction, thereby allowing the printing plate abrasive.

不小家都懂得，网纹辊、印版滚与不抬印滚之间虽说是滚不抬，但是网纹辊、印版辊与不抬印辊是有不抬缩的，而不一辊的线速量又是分歧的，所以当不弛力过不小时，由于印版被不抬缩会与网纹辊之间爆发必定的滑动摩擦，从而使印版爆发磨损。

When using the die-cutting tool, be sure to use industry gently rolling shouder strickle blankets up drop every day in order to maintain an adequate amount of lubricant die-cutting knife at the end of shouder hobber and the stone the roller surface clean, and in both form a thin film to improve die-cutting knife at the end of shouder hobber and rolls of anvil wear resistance.

搁置模切刀时，一不退给对峙搁置厂家供答的滚肩刮拭毛毡，每天进取滴适度润滑油，以保留模切刀滚肩与底砧辊暗不天的肮脏，且在两者间变成一层薄薄的油膜，恶化模切刀滚肩与底砧辊暗不天的耐磨损性能。

Figure 2 printing plate gaskets is higher than the 0.2 ~ 0.3mm hobber pillow, blanket below the occipital hobber 0.05mm, a2, B2 Department produces a smaller convex hull, of course, less friction and sliding, wear plates, no szlama and "" taping, fault-printing plates and high, less hierarchical dot gain, clearly, the life expectancy of the machine, the electrical power consumed less.

图2印版的衬垫矮于滚枕0.2～0.3mm，橡皮布矮于滚枕0.05mm，在A2、B2处爆发的凹包较小，当然摩擦和滑动也多，印版磨损较多，无不推不净和"杠子"障碍爆发，印版的耐印率矮、网不面放大多，条理纯楚，机械的寿命放大，电机耗电也多。

Its content was only 0.945%±0.492％ of the disc dry weight.The elastin was obviously reduced at deep laminae of annulus fibrosus.④On the elastin fibers of the pathological discs,the fraying,irregular holles,crevice were showed.

突出椎间盘弹性蛋白纤维密度降低，含量明显减少，仅占椎间盘干重的0.945%±0.492％，尤以纤维环深部降低明显，弹性蛋白纤维上出现磨损、裂隙、不规则空洞等。

Should check whether the wheel rim deformation; wheel has a horizontal deflection or radial swing; shock absorber has loose or worn; turned horizontal, the ball straight rod section, or has loose steering gear assembly; spring steel U - shaped bolt, the center clamping bolts loose or whether there is any damage; Caster is correct; tire pressure is correct

应检查车轮轮辋有否变形；车轮有否横向偏摆或径向摆动；减震器有否松动或磨损；转向横、直拉杆球节，或转向器装配有否松动；弹簧钢板的U形螺栓、中心夹紧螺栓是否有松动或损坏；后倾角是否正确；轮胎气压是否正确。

Should check whether the wheel rim deformation; wheel has a horizontal deflection or radial swing; shock absorber has loose or worn; turned horizontal the ball straight rod section or has loose steering gear assembly; spring steel U - shaped bolt the center clamping bolts loose or whether there is any damage; Caster is correct; tire pressure is correct

应检查车轮轮辋有否变形；车轮有否横向扁摆或径向摆动；减震器有否松动或磨损；转向横、直拉杆球节，或转向器装配有否松动；弹簧钢板的U形螺栓、中心夹紧螺栓是否有松动或败坏；后倾角是否正确；轮胎气压是否正确。

The equipment use ceramic, horniness alloy classification impellerpump to make the abrasion very little.

设备能超细加工莫氏硬度七级以上的坚硬物料，陶瓷、硬质合金分级叶轮的应用使机器的磨损极小。

The experiment results showed that HOS could be used to distinguish different tool wear styles.

实验结果表明，利用高阶量可以有效区分刀具磨损的不同阶段。

During their study, the researchers first examined the teeth of modern-day capuchins, howling monkeys, and other monkey species to discern the marks left by fruits, seeds, and other plants.

昂加尔解释说：我们通过现有的物种和已知的食物来了解他们牙齿的微磨损图案有什么不同。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。