碳化的

The influence of solid-solid transition on the wax precipitation was considered in the correlation of standard fugacity ratio.

当温度低于旋转化温度时，烷烃成为低能量不可转化的β晶体，其间不同碳原子数的正构烷烃都经历了固-固转换。

Carbon nitride powder with C-N bond was prepared. High pressure and temperature were supplied by Cyclonite and dicyandiamide(C2H4N4) was used as the primary precursor in this article.

利用黑索今炸药作为高温、高压源，双氰胺(C2H4N4)作为主要前驱体，采用爆炸冲击合成的方法制备了含C-N的氮化碳粉末。

Transformation process and microstructure in 675 armor steel continuously cooled at a series of different rates were investigated using a high-resolution dilatometer,along with optical and transmission electron microscope.

675装甲钢是一种中碳高强度低合金钢，是在685装甲钢成分基础上加入少量V进行微合金化而得到的，其所含主要合金元素有Ni、Mo、Cr和V，其中Ni、Mo、er主要是强化铁素体和提高淬透性，V主要起沉淀强化和细化晶粒的作用。

Furthermore, we also studied the coupling reaction of alkenes with alkynes initiated by carbopalladation catalyzed by divalent palladium.

另外我们还对炔烃碳钯化启动的烯炔偶联反应进行了初步的探索。

The formation of 1,3- and 1,6-DMC resulted from methylation at ring carbon 3 and 6, which have identical reaction activities, in 1-methylcarbazole in kerogen matrix with identical rate. The 1,4- and 1,...

相对于1，3-DMC和1，6-DMC而言，1，4-DMC和1，5-DMC显示出相当一致的变化趋势，表明了在1-甲基咔唑进一步的甲基化中，3、6与4、5环碳位上存在竞争性反应过程。

It could be concluded that there is no definite evidence and effective method for synthesizing a carbon nitride crystal.

分析表明：现有的研究结果还没有给出氮化碳晶体合成的确信证据。

Strong evidence shows that crystalline carbon nitride films have been synthesized.

因此有足够的证据表明，晶态的氮化碳薄膜已经合成。

Zhenrong Company main products are: box-type furnace, furnace cars, Pit Carburizing Furnace, Pit Type Furnace, Pit nitriding furnace, electric oven blast, salt-bath furnace, mesh belt electric furnace, new coal-fired reverberatory furnace, rod heat treatment furnace, glass-lined equipment, resistance furnace and various industrial furnaces, and undertook a variety of industrial electric furnace repair and supply of various electric fittings.

振荣公司主要产品有：箱式炉、台车炉、井式渗碳炉、井式回火炉、井式氮化炉、电热鼓风干燥箱、盐浴炉、网带式电炉、新型燃煤反射炉、抽油杆热处理炉、搪玻璃设备电阻炉及各种工业用炉，并承接各种工业电炉的维修及供应各种电炉的配件。

Microstructure evolution in eutectoid steel during warm deformation in the temperature range from 600 to 700℃ was investigated by simulating hot compression test, SEM and thermomagnetic measurement. The effects of deformation and subsequent annealing on the spheroidizing of pearlite, refining of microstructure and dissolution of cementite were studied.

利用热模拟压缩变形、SEM和热磁法实验，研究了共析钢在600~700℃变形过程的组织演变规律，探讨了变形及随后保温过程对珠光体球化、组织超细化和渗碳体溶解、再析出的影响。

The carbon-bearing pellet s made of zinc-bearing dust and sludge,iron concentrates and additive of agglomerant were reduced at 1 000~1 200 °C,the effects of different kinds of additive and reduction temperature on the strength and metallization rate of carbon-bearing pellet s were studied.

将含锌尘泥、铁精矿及粘结剂混合造成的含碳球团在1050~1250℃条件下还原，研究了不同粘结剂、不同温度对其强度及金属化率的影响。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。