碳化物

The characteristic of the new process is heating under Acltemperature for suitable time to change lamellar Sorbite to ginger-likeSobite.

介绍了一种工具钢在稍低于Acl温度下不太长时间加热，使片状索氏体不完全球化，形成姜块状碳化物的工艺。

The characteristic of the new process is heating under Acl temperature for suitable time to change lamellar Sorbite to ginger-like Sobite.

工具钢在稍低于Acl温度下不太长时间保温，可使珠光体片不完全球化，形成姜块状索氏体，淬火后得到马氏体＋姜块状碳化物组织。

The results show that 82B wire rod brittle fracture is mainly caused by excessive inclusion,reticulate carbide,lower sorbite in the microstructure,and surface defect of wire rod.

结果表明，82B钢盘条脆断的主要原因是夹杂物级别超标、组织中出现网状碳化物、索氏体含量偏低以及盘条表面缺陷等。

Due to high carbon and alloys content, high speed steel is of heavy carbide segregation, narrow forging temperature range and poor ductility, therefore, 4~6 heatings were needed when the ingot was forged into finished products with steam hammer.

高速钢的碳和合金元素含量高，碳化物偏析严重，塑性差，锻造温度范围比较狭窄，采用汽锤锻造，由钢锭轧成材需要4~6火次。

With X-ray diffraction and TEM analysis,it is proved that the microstructures of both undeformed and deformed matrixes are austenite and carbide with some striation structure in the matrixes,the amount of stripes in the deformed matrix is obviously more than that in the undeformed matrix.

通过X衍射和电子显微分析证明，变形前和变形后的基体组织都是奥氏体基体加上碳化物，变形前后的基体中均存在条纹状组织，且变形后基体中的条纹数量明显高于变形前基体中的条纹数量。

The matrix structure of composition is WC, W2C, M7C3, M23C6, M6C, M12C carbide and Troostite.

复合层组织为：WC、W_2C、屈氏体、M_7C_3、M_(23)C_6、M_6C、M_(12)C等碳化物。

The experiments show that the remelting hardening layer consists of melting zone, quenching zone and heat affected zone. From surface to internal, the respective microstructures are extremely small hidden-crystal martensite and a few residual austenites, hidden-crystal martensite and carbides and residual austerite, martensite and backfire troostite and ferrite.

实验表明：熔凝硬化层由熔化区、相变硬化区和热影响区组成；由表及里组织分别为极细隐晶马氏体＋少量残余奥氏体、隐晶马氏体＋碳化物＋残余奥氏体、马氏体+回火屈氏体+铁素体。

The effect of solution and tempering temperature on the Charpy V impact energy AKV and HRC of ultra-high strength steel 23Co14Ni12Cr3Mo was studied, impact fracture surfaces were observed by SEM,and the undissolved carbide was analyzed by TEM.

研究了不同固溶及回火温度对高Co-Ni超高强度钢23Co14Ni12Cr3Mo的Charpy V型缺口试样冲击功AKV和硬度HRC的影响，并用扫描电镜观察分析不同处理状态下的冲击断口形貌，用透射电镜对未溶碳化物进行了分析。

On the basis of examination of the wear behavior and worn surface morphology of the coatings after abrasive wear and erosion wear respectively, and the enhancing mechanisms of interlamellar bonding caused by unmelted carbide particles during deposition, the effects of the microstructure on its performance are discussed.

其次，在分析研究了涂层磨粒磨损和冲蚀磨损失效形貌以及未熔化碳化物颗粒对涂层层间结合强化机理的基础上，探讨了磨损机制、磨损模型的建立及涂层结构对磨损性能的影响规律。

The service life of wire drawing dies of Cr12 steel treated by new process is near 2 times than that of under normal heat treatment.

本文通过对Cr12钢热处理工艺的试验研究以改善Cr12钢的碳化物形态与分布，达到提高Cr12钢冷

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。