硬件实现的

After reviewing the historical development of fur animation ,this paper presents some algorithms and methods to implement real-time fur animation in the aspects of modeling,rendering and animation.

本文在回顾毛发动画技术发展历程的基础上，结合当前的图形硬件发展水平，从建模，渲染与动画三个方面分别论述了实现实时毛发动画的相关算法与技术。

The hardware configuration and software designing of FCS for saturated vapour flow were given in the article.

介绍一种控制系统，它的硬件采用先进的现场总线压力变送器和涡街流量计，软件采用分段变系数补偿法，实现了饱和蒸汽的质量流量测量。

The motor is competent for long low-speed or stopping up and the clutch has fine characteristic of control with torque. Sensors as forward access obtain signal, an industrial computer with abundant hardware resource as background utilize set-in boards based on PCI bus and serial modules to fulfill data transmission and instruction communication.

传感器作为前向通道拾取各信号，后台以工业控制计算机丰富的硬件资源为基础，利用基于PCI高速总线的插卡式测量板卡和串口模块实现与计算机的数据传输和命令通讯。

This paper introduces the structure and the principle of auto board shears, and also presents the design method of hardware and software implemented by 8051 single chip microcomputer.

摘要 介绍了自动剪板机系统的结构组成和工作原理，叙述了8051单片微机实现其生产过程控制的硬件与软件的设计方法。

Omron therefore chosen to achieve series-CPM1A slicer control, but also designed in accordance with the specific requirements of the PLC hardware circuit, as well as the preparation of plans trapezoidal procedures, and ladder diagram software process simulation

因此选用欧姆龙-CPM1A系列来实现切片机的控制，同时根据具体要求还设计了PLC的硬件电路图，以及梯形程序图的编制，并对梯形程序图进行软件仿真

This design keep the twice frequency transform and the superheterodyne structure in analog receiver,and use programmable Direct Digital Synthesizer in RF section.

在此基础上还介绍了两种常见的软件无线电实现方案以及依赖的硬件平台，并提出了适合本设计背景的短波定时接收机方案。

This paper introduced the design and development of a virtual frequency sweeper based on DDS technology.

介绍了基于DDS技术的虚拟扫频仪的硬件与软件设计，并详述了DDS技术以及用该技术实现扫频信号源的方法。

This technique made full use of the functions of DMA Chaining and hardware interrupts of DSP,realized the synchronousness successfully between receiving and processing of the data,Then it restored the CW signal successfully by structuring a cancelling- chopper -sequence.

该技术充分利用了DSP提供的链式DMA和硬件中断等基本技术，成功地实现了数据接收与处理的同步，进而通过构造去斩波序列成功将连续波信号还原，经过量程判断之后，准确地计算出连续波信号采样数据的平均值。

Finally, several MTNCs were designed for implementing the XOR operation and Literal, AND, OR operation in ternary logic at switch level. The result of simulation with PSPICE showed that the designed circuits had not only the correct logic function and small propagation delay but also had simple structure. Whats more, when achieving the same logic function, the MTNCs decreased large amount of hardware expense compared with the STN circuits.

对设计出的电路进行PSPICE模拟并测量相关参数，结果表明，该设计方法不但简便、规范，而且设计出的多阈值神经元电路具有速度快，结构简单的优点，并且，在实现相同逻辑功能时，采用多阈值神经元电路相对于单阈值神经元电路，大幅降低了硬件成本。

It is important to implement transcendental function of high precision with proper hardware cost for high performance microprocessor design.

如何以合理的硬件代价，快速实现高精度的浮点超越函数，是高性能微处理器设计的关键问题之一。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。