硅剂

The influence of factors such as W/C,sand percentage,water reducing agent and wollastonite is analyzed and the optimum proportion is given in this paper.

阐述了研究开发特重高强混凝土的重大意义，提出了制备技术和途径，说明了原材料及其性能要求，介绍了正交试验法设计特重高强混凝土配合比的方法，分析了水灰比、砂率、减水剂和硅灰等因素对特重高强混凝土的影响，在此基础上给出了最优配合比。

Through FIR and SEM analyses, it was found that the silane coupling agent could react with the surface of wood flour, and the adhesive strength between HDPE and wood flour as well as the mechanical properties of the composite was improved.

通过FIR和SEM分析发现，硅烷偶联剂可与木粉表面发生化学反应，从而提高了HDPE与木粉的界面粘合强度，使复合材料的力学性能得以提高。

Highly ordered mesoporous Zr-Ce-SBA-15 silica with hexagonal-platelet morphology was synthesized through a hydrothermal route by using pluronic P123 as a template, tetraethyl orthosilicate as a silica source, zirconyl chloride and cerous nitrate as a precursor. The main strategy of this method was to utilize the acidity self-generated from the hydrolysis of inorganic salts in the aqueous solutions, where no addition of mineral acids was necessary.

以P123为模板剂，正硅酸乙酯为硅源，氯化氧锆和硝酸亚铈为无机前驱盐，在不外加无机酸的条件下，利用无机前驱盐自身水解产生的弱酸性环境，通过水热合成路线一步合成了具有大的径轴比、短孔道、六方板状形貌的Zr-Ce-SBA-15介孔材料。

Water,dimethicone,propylene glycol,glycerin,cyclomethicone,ppg-15 stearyl ether,sorbitan oleate,stearic acid,cetyl alcohol,glyceryl stearate,ethylhexyl methoxycinnamate,peg-100 stearate,panthenol,phenoxyethanol,phospholipids,triethanolamine,methylparaben,oenothera biennis oil,imidazolidinyl urea,carbomer,c12-13 alkyl lactate,glycyrrhetinic acid,citrus aurantium dulcisoil,propylparaben,tocopheryl acetate,benzophenone-3,triclosan,disodium edta,ethylparaben,pentadecalactone,iris germanica root extract,retinyl palmitate,bisabolol,butylparaben,sodium hyaluronate,aesculus hippocastanumseed extract,ruscus aculeatus root extract,chlorhexidine digluconate,biosaccharide gum-1,citrus aurantium amaraoil,tocopherol,lecithin,ascorbyl palmitate,glyceryl oleate,BHT,citric acid,limonene,linalool

水， 地美司康，丙二醇，甘油，环甲硅脂， PPG-15 硬脂基醚，油酸己六酯，硬脂酸，十六醇，甘油硬脂酸， 4-甲氧基肉桂酸-2-乙基己基酯，聚乙二醇硬脂酸酯，维生素B5，苯氧乙醇，磷脂质，三乙醇胺，羟苯甲酯，月见草油，尿素醛，卡波姆， c12-13烷醇乳酸酯，甘草亭酸，甜橙油，羟苯丙酯，醋酸盐维他命E，二苯酮-3，玉洁新，乙酸乙二胺二钠，羟苯乙酯，环十五内酯，鸢尾花根萃取，维他命A酯，没药醇，羟苯丁酯，透明质酸钠，欧洲七叶树籽萃取，假叶树根萃取，洗必泰葡萄糖酸盐，多醣物质，苦橙油，维生素E，卵燐脂，抗坏血酸棕榈酸酯，甘油油酸酯，二丁基羟基甲苯，柠檬酸，柠檬精油，芳樟醇水：几乎所有护肤品成分第一位都是水。地美司康：即silicon，矽灵，一般添加于霜剂中，使用后皮肤手感光滑。该成分不可吸收。

The effects of flurocarbon surfactant,silane coupling agent, epoxy acrylate prepolymer and alumium silicate fine powder on the water resistant of acrylate structural adhesives were studied.

研究了氟碳表面活性剂、硅烷偶联剂、环氧丙烯酸酯预聚体以及硅酸铝粉末对丙烯酸酯结构胶耐水性的影响，制备出一种耐水性能优异的丙烯酸酯结构胶，其常温拉伸剪切强度为24。

The effect of polydimethy siliconoxiane,silicon oil,auxiliary additives and emulsifier on defoaming and antifoaming is investigated.

讨论了聚二甲基硅氧烷、硅膏、辅助填料、乳化剂等对抑泡、消泡性能的影响。

This product is o high effective antifoaming agent of rganosilicon polyether graft copolymerization, which can effectively solve the bulb from the drilling, and prevent from making bad influence to production.

本品是一种有机硅聚醚接枝共聚高效消泡剂，它可有效解决钻井产生的泡末，避免给生产造成不良影响。

The special antifoaming agent JY-1 which possessed the features such as strong antifoaming power,rapid foam+broken,rapidity of breaking foam,good stability,high temperatuer,low cost and so on can be widely applied in industry.

结果表明，JY～1有机硅乳液抑泡剂具有抑泡力强，消泡速度快，稳定性好，耐高温，成本低等特点，可作为腈纶油剂的专

An injection rate of 15μg/g CDF-10 antifoaming agent was normally injected to the top of the coke drum at the final 2-6 h of the coking cycle. It could eliminate 3m foam and increase the effective utilization ratio of the coke drum from 65%to 78%, and resulted in higher throughput. The said antifoaming agent had no poison effect on hydrogenation catalyst.

应用结果表明， CDF-10消泡剂一般于生焦周期的最后2～6 h，以15 μg/g 的量在焦化塔顶注入可以将焦炭塔内泡沫层消除3 m，使焦炭塔的有效利用率由65%提高到78%，处理量也可相应提高，并且不会造成对加氢催化剂的硅中毒。

The invention discloses a dielectric hole-microhole composite material and synthesizing method in the inorganic porous material, adsorbing material and catalytic material technical domain, which comprises the following steps: adopting zeolite molecular sieve as raw material; reacting with sodium bisilicate solution under 30-60 deg.c for 10-300 min; disintegrating particle part of zeolite molecular sieve into piece with microhole structure; adding cetyl trimethyl ammonium bromide as molder; adjusting pH value of mother liquid to 10-12; aging 1-8h; adding in the high-pressure autoclave to do water heat synthesizing reaction at 80-130 deg.c for 24-72h; separating solid; washing; drying; sintering under 500-600 deg.c for 5-10h; obtaining the Si-Al porous material with dielectric hole and microhole composite structure.

本发明属于无机多孔材料、吸附材料和催化材料技术领域，涉及具有介孔-微孔复合材料及其合成方法。其特征是以沸石分子筛为原料，用偏硅酸钠的水溶液在30～60℃反应10～300分钟，使沸石分子筛的颗粒部分解离形成具有微孔结构的碎片，加入模板剂十六烷基三甲基溴化铵，然后调节母液pH值为10～12，老化1～8小时，然后加入高压釜于80～130℃进行水热合成反应。反应24～72小时后，分离出固体，水洗、干燥，然后于500～600℃焙烧5～10小时，得到具有介孔和微孔复合结构的硅铝多孔材料。本发明的效果和益处是所发明的合成方法可用于合成多种沸石结构和介孔结构的复合材料，所合成的材料经过质子交换可以具有较强的酸性，在吸附和催化领域具有广泛应用前景。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。