石墨的

The heat conductivity of material improves rapidly by the content of the graphite increasing,and the heat conductivity preponderates over 1.7 w/ when the content of graphite is 5% in the material .

材料的热导率随着石墨粉含量的增加几乎成直线上升，当石墨含量为5%时材料的热导率大于1.7W/。

The utility model is characterized in that one layer of conducting film composed of nickel chloride, chrome oxide, antimony chloride or graphite, etc. is arranged at the bottom of the vessel.

实效模型在引导电影的一层镍氯化物、铬氧化物、锑氯化物或者石墨组成中被表示的特色，等等在船的底部被安排。

Methods Thallium was oxidized to thallium by bromine water and the thallium was complexed to [TlCl4](superscript -) in 20mL/100mL HCl and absorbed by polyurethane foam. The adsorbed thallium was eluted by a boiling Water bath and determined by platform-GFAAS.

以溴水将水样中的Tl氧化为Tl，在20mL/100mL的盐酸中Tl转化成[TlCl4]并为聚氨酯泡沫吸附，吸附的[TlCl4]经沸水浴洗脱后以平台石墨炉原子吸收法测定。

Using diamond carbon source has greatly improved the synthesis efficiency.

此过程增加了石墨与金属接触的面积，也增加了碳的溶解量并降低了碳的浓度梯度。

In this paper several technologies, such as Fourier transform infrared spectroscopy, elemental analyzer, wide angle X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and high resolution transmission electron microscopy were used to systemically investigate the evolution of crystal structure, chemical structure, microstructure and properties of wet-spinning and dry-jet wet-spinning PAN precursor fibers during proxidation and carbonization process, analysis the structural change of carbon fibers during graphitization, and discuss the correlation between the structure and properties.

本文采用傅里叶变换红外光谱、元素分析仪、X射线衍射仪、场发射扫描电镜、透射电镜以及高分辨透射电镜等测试技术，分别系统研究了湿纺原丝和干喷湿纺原丝在预氧化和碳化过程中纤维晶体结构、化学结构、微观结构和力学性能的演变规律，分析了碳纤维在石墨化过程中的结构转变，并对碳纤维结构与性能的相关性问题作了探讨。

Evidence shows that small graphite flakes were formed and come off from the surface of the diamond powder.

此结果会使蒸发出来的蒸气中，金属与碳的比例在空间分布上更均匀，因而提高被石墨完整包裹GEM的良率。

For physisorption of organic molecules on chemically inert graphite, the interaction between the adsorbates and the substrate was very weak, which provided an opportunity to image the molecules with a minimum of substrate perturbation.

有机分子物理吸附在惰性基底石墨上时，分子和基底之间的相互作用很弱，吸附分子的STM图像反差主要由分子本身的性质决定。

The research results show that:(1) Brass is a binary alloy of copper and zinc, because its casting temperature is high, the freezing temperature of brass and zinc is different, it is inevitable to produce educts that adhere to the graphite crystallizer's surface during the solidification.

黄铜扁锭水平连续铸造气体保护方法的研究结果表明：(1)因为黄铜是铜锌二元合金，由于其铸造温度高，黄铜与锌的凝固温度不同，在凝固过程中不可避免的要产生析出物附着在石墨结晶器表面。

After looking up a large amount of native and foreign information, the materials used in the experiment were as follows: PTFE base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. The experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization.

经过查阅大量国内外文献资料后确定原料为：聚四氟乙烯树脂为基体，加入石墨、二硫化钼、铜粉、碳纤维等填料；试验方法为：根据均匀试验方法设计配方，用样条函数找出配方与摩擦性能的关系，然后在拟合曲线上选取具有代表性的试验点进行验证试验，达到优化的目的；制备工艺：冷压烧结法制备固体润滑剂。

Two bismaleimide fiber composites filled with graphite and copper were prepared by laminate molding process. The effect of graphite and copper content on the tribological properties of composites were investiged. The morphology of the composite worn surface was observed by scanning electron microscopy.

采用层压成型制备了2类改性双马来酰亚胺纤维复合材料，分别考察了石墨、铜粉的用量对纤维复合材料摩擦性能和力学性能的影响，并用扫描电镜对复合材料的磨损表面形貌进行了分析。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。