矩

A new method for calculating loss torque of coiler is introduced. After loss torque of coiler was calculated and compensated by the new method, system tension was stable, operation was reliable, thin strip break event was eliminated, and yield was improved.

本文介绍了一种计算卷取机损失转矩的新方法，采用该方法对损失转矩进行计算并补偿后，系统张力保持稳定，运行可靠，克服了以往薄带容易断带的现象，提高了成品率。

Also in this dissertation, in order to assist the project of simulating cometary spectra of H〓O〓 as proposed by Kawakita and Watanabe Ap.

为了协助Kawakita和Watanabe[Ap.J.574（2002）L183-L185]提出的H〓O〓彗星光谱的理论模拟和进一步标识H〓O〓的实验谱线，本文首次利用偶极矩的从头计算结果计算了振动跃迁矩及谱线强度。

This paper adopts auto-threshold value technology which can select better threshold value. This paper puts forward rotating projection moment invariants which optimizes moment invariants and identifies conglutinate letters.

本文采用了自动阈值选择技术，使阈值的选择更合理；对不变矩进行了优化，首次提出了旋转投影不变矩方法，适合粘连字符地识别。

B0 is also called the constant term or the intercept term, or intercept parameter.

b0也被称为常数项或截矩项，或截矩参数。

Compared with Vector Control, the main advantage of DTC is that it directly controls flux and torque.

与矢量控制相比，直接转矩控制的主要优点是直接对电机的磁链和转矩进行控制。

Via the stochastic averaging method, the four-dimensional system is reduced to a two-dimensional one. Through the logarithmic polar transformation , and then Girsanov theorem and Feynmann-Kac formula, the backword differential operator is then obtained. By expanding the eigenfunctions as a Fourier cosine series, the approximate analytic expansion of the moment Lyapunov exponent is then obtained.

首先在经典二元机翼颤振方程加入随机激励，通过随机平均法，Girsanov定理和Feynmann-Kac公式得到关于矩Lyapunov指数的特征值问题，其次采用Fourier余弦级数对特征函数进行正交展开得到系统矩Lyapunov指数的近似解析式。

By considering torque characteristics of variable-frequency motors and mesh stiffness as well as backlash nonlinearity in gear transmission,a dynamics model for the cutting system of shield tunneling machine with redundant drives was established. The fluctuation characteristics of torque loads and dynamic cutterhead driving torque in composite strata were analyzed.

复合地层掘进扭矩载荷突变是造成盾构机掘进过程中堵转停机的直接原因，考虑盾构机刀盘驱动变频调速电机特性、转矩传递过程中齿轮啮合刚度及齿侧间隙等非线性因素，建立冗余驱动的盾构机刀盘切削系统机电耦合动力学模型；针对典型复合地层地质条件，对盾构机在上软下硬地层掘进过程中刀盘驱动转矩动态特性进行仿真分析。

Spatial white noise is considered first then the spatial colored noise. Two method based on 1st and 2nd order cyclic moments, CERA, and then 3rd order cyclic moment, MCERA, are proposed separately.

分白噪声及有色噪声两种情况，分别提出了基于一、二阶循环矩的CERA方法和基于三阶循环矩的MCERA方法。

Since the different dynamics methods such as Newton-Euler method, Lagrange's equations and other methods can be used to develop the dynamic equations of global system, the two different forms of the dynamic equations are ordinary differential equations and differential algebra equations.

通过结合有限段法和多体系统动力学离散时间传递矩阵法，形成了非线性梁有限段离散时间传递矩阵法，该方法保留了有限段法适用于几何非线性大变形分析、自动考虑动力刚度项等优势，又保留了DT-TMM-MS建模方便灵活的特点。

The value of dipole moment can be conferred from the situation of the molecular symmetry, and vice versa.

偶极矩沟通了分子的微观结构与宏观性能特征，所以进行化合物偶极矩的计算和研究，具有十分重要的理论意义和工程价值。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。