着重

Detailed studies are made as follows: Searching the key internal factors which can affects slope stability. According to the geological data which was gained by exploration investigation, establishing a geological model which can reflect rock mass characteristics;With analyzing the internal and exterior factors synthetically, the deformation and possible failure mechanism and mode of the cut slopes was confirmed which combines with stereoic projection and other techniques;The stabilities of the 14 high slopes are estimated synthetically by applicable design codes and guidelines. With the estimate result and some other analysis methods, the rock mass mechanical parameters of slope are identified;As a results, 14 high slopes fall into 4 categories based on rockmass characteristics and discontinuities. The stability and deformation of some typical slopes was analyzed with distinct element method by UDEC;The safety factor of some dangerous slopes are calculated by rigid limiting equilibrium method for coMParison.

首先着重研究影响边坡稳定性的内在因素，主要是通过地质勘探、测量、现场观测等手段取得研究区地质体的基础地质资料，建立起能够反映地质体结构特征的地质模型；随后综合分析潜在的内外部影响因素，并结合赤平投影对边坡可能的失稳模式或破坏机制作出判断；运用已有岩体质量分类方法对沿线14个高陡边坡稳定性进行初步的评价，并结合试验研究、经验判断、工程类比等手段确定了坡体的岩体力学参数；根据稳定性初步评价结果将研究区14个高陡边坡按开挖方式分为4大类，并利用离散元程序UDEC对各类典型高陡边坡进行了稳定性计算分析；对潜在危险边坡利用刚体极限平衡法求出了不同工况下的安全系数。

This paper has created the mathematical model of the hydraulic system of the steel bar cutter, considered the hydraulic power unit, accumulator and hydraulic pipe, specially the dynamic characteristics of the hydraulic cylinder buffer structure.

本文建立了高速钢筋切断机液压系统的数学模型，充分考虑了液压动力元件、蓄能器及液压软管等元件的影响，着重分析了液压缸缓冲结构的动态特性。

This paper mainly researches high speed milling TC4 and discusses the problem about cutting force during the process of high-speed milling.

着重讨论了钛合金TC4高速铣削过程铣削力的问题，研究了切削参数、刀具磨损及刀具材料等对铣削力的影响。

The aggregates and relevant fluorescence spectra of three cyanine with higher sensitizing efficiency in different solvents andin different concentrations were studied.

本文着重研究了三只增感效率较高的菁染料在不同溶剂和不同浓度下的聚集态和荧光光谱。

The copolymerization of cycloolefin and α-olefin, and structure of the obtained polymer are significantly affected by the structure and symmetry of metallocene catalysts, electronic effect and steric hindrance of ligands.

着重介绍了加成聚合法中茂金属催化剂的结构对称性、配体的电子和体积效应、反应条件等对聚合活性、产物组成与序列分布及相关热性能的影响。

The copolymerization of cycloolefin and α-olefin,and the structure of the obtained polymer are significantly affected by the structure and symmetry of metallocene catalysts ,electronic effect and steric hindrance of ligands.

着重介绍了加成聚合法中茂金属催化剂的结构对称性、配体的电子和体积效应、反应条件等对聚合活性、产物组成与序列分布及相关热性能的影响。

The mathematical model of reliability design for shaft rigidity was established based on reliability inference theory.Reliability calculation of cylinder shaft rigidity of press was proceeded and regularity of cylinder shaft rigidity reliability as the condition change was found.

应用可靠性设计相干理论建立了轴的刚度可靠性设计的数学模型，着重探讨印刷机印刷滚筒轴的刚度可靠度的计算，并得出不同条件下印刷滚筒轴刚度可靠度的变化规律。

The next step is to found the model of a cylindrically layered borehole embedded in poroelastic media.

首先分析了声波在孔隙介质中传播时渗流运动的特点，着重讨论了附加质量和动态渗透率的意义。

This paper stressed on the fact that electric displacement vector is a supplementary physical element,focused on a difference between D and D surface integral and on the condition of D=ε_0E_0 existence,and made a comprehensive and correct understanding for beginner.

着重说明了电位移矢量D是一个辅助物理量，强调指出D与D的面积分的意义不同，以及D=ε0E0成立的条件，从而使初学者对D建立起一个全面和正确的认识。

Methods Retrospectively analyzed the clinical data of the 4 DAA associated with complex cardiac anomalies patients,focused on the surgical methods and the results of the operation.

方法回顾性分析4例双主动脉弓合并心内畸形患者的临床资料，着重分析手术方法和手术结果。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。