相切的

Calculation of teeth profile of disc cutter for arc-gear;2. The formulas for setting angle and entrance angle of disc cutter s are derived by using the contact condition of space curve.

利用空间曲线相切条件导出了用于计算盘形刀具安装角和切入角的条件；该方法具有以下优点：无需知道工件齿形，可同时获得刀具宽度、半径等参数。

5 Create the inferior screw model Bisectioning the included angle between exterior and interior screw and theincluded angle between ecto-upper and ento-upper screw in AutoCAD2006 software,Create a plane traverse the two bisection points and the core of the pedicle.

采用上述辅助定位后如遇椎弓根部穿破情况则需要手动调整螺钉以使螺钉刚好与原穿破侧椎弓根骨壁相切。 1.2.5创建下侧进钉方向的椎弓根螺钉模型：在AutoCAD2006程序中将椎弓根螺钉内外夹角、上方夹角两等分，由同侧两等分点与椎弓根中心点共同创建一平面，依该平面与同侧球在下终板平面交点创建下方螺钉模型。

This optimal allocation yields the highest level of utility (at point C , the tangency of the capital allocation line and the highest indifference curve).

该最优配置使得投资者效用最大化（在 CAL 线和无差异曲线的相切处 C 点达到）。

Tangent surface ...

最后，可使用"相切曲面"对话框中的"曲线"选项页编辑参照曲线。

Be sure to select the edge, not the circle because we need the tangency from that su***ce

一定要选择的边缘，而不是圆形，因为我们需要从表面相切

Through Z a line is drawn tangent to the circle centred at Y.

过Z 作一条直线相切於以Y 为圆心的圆形。

The supramastoid crest and the superior rim of zygoma arch correlated with the level of the bottom of the middle fossa.

颞底经小脑幕手术入路骨窗为：第1孔位于乳突上嵴上，孔的后缘与顶乳突缝前角相切。

In [2], we also consider nondegenerate homoclinic tangency and shows that the homoclinic point is accumulated by a sequence of uniformly hyperbolic invariant sets.

在[2]中，我们研究非退化性的同临相切，证明了同临相切点会被一串一致双曲不变集所聚集。

If c is the largest slope of the tangents from the point to the circle , find the value of c.

6 图三 Figure 3 现有点和圆。如果c是通过点与圆相切直线的最大

First, it is always possible to circumscribe a sphere in a camera-aligned quad.

首先，它总能保证和一个与摄像机对齐的矩形相切。

The reasons of iron ions content overproof in grade Ⅱ desalting water system,such as variation water quality,contamination of regenerant , operation adjustment of pretreatment system and switching operation of bed were discussed.

对二级脱盐水系统中铁离子含量超标的原因，如来水水质发生波动、再生剂受到污染、预处理系统操作调整、床体运行切换等进行了论述。

You were hired to drum up new business, so go and do it.

公司雇你招徕新业务，你就做你的事好了。