直线运动

In existing technology, the nonnal way is adopting the four-bar linkage mechanism to imitate the arc or the linear movement. On the theoretical analysis, its movement precision can meet the requirement, while in the operation, because of the abrasion of bearings in gemel, which do much greater effect on movement than the former, its movement precision goes much beyond the theoretical value.

现有技术中一般是采用四连杆机构来仿弧线或直线运动，从理论上讲其运动精度是能够满足要求的，但在实际使用中，由于铰链点轴承的磨损（另外，装配时也预留了一定的轴承间隙），对运动轨迹产生的影响很大，其运动精度就大大超出理论值。

A particularly investigation is carried out to the observibility of in-flight alignment using numerical simulation when the aircraft performs four kinds of basic maneuvre, namely linear acceleration, yawing, pitching and rolling. The thesis summarizes the two kinds of maneuvre. Simulation results show that the precision of transform alignment reach 5 minutes in 10 seconds if the aircraft performs two well-defined maneuvres.

首先本文采用数值分析的方法研究了直线运动、航向角运动、俯仰角运动和横滚角运动对传递对准系统可观性的影响规律；再结合飞机的实际运动，给出了空空导弹传递对准时的飞机飞行轨迹；"蛇形"飞行轨迹和摇摆运动飞行轨迹，仿真结果表明：按这两条飞行轨迹机动，在10s内传递对准精度可达到5′以下。

Motion synchronization between tool in X direction and principal axis rotation was controlled by electronic gearbox in cam turning. And profiling mechanism could be superseded by servo tool-holder. Linear motor direct drive servo tool-holder was designed, and host-slave control system with PC and DSP was developed for the require of high-speed and realtime servo. The technical process was analyzed in cam turning. Servo tool holder with tool swinging and principal axis variable rotate speed were presented to keep constant cutting angle and speed.

将电子齿轮箱用于凸轮车削加工系统的传动，以伺服刀架取代了传统加工的靠模装置，实现了刀具X方向直线运动与机床主轴转动的同步控制；设计了直线电机直接驱动的伺服刀架及基于PC与DSP构成的上—下位机控制结构，采用DSP进行实时控制以满足高速伺服需要；对凸轮加工过程的工艺特点与恒角度、恒速度车削进行研究，提出了具有刀具摆动功能的伺服刀架与机床主轴变转速运动方案。

Puts forward a novel method that is called the method of pseudo base point, which is much simpler than the classic methods when used for analyzing composite motion of rigid multi bodies if the convected motion is planar motion and the relative motion is rectilinear motion.

首次提出用伪基点法进行多刚体系平面复合运动的速度和加速度分析，此法对牵连运动为平面运动、相对运动为同平面直线运动的问题求解比经典方法简便得多。

It, thereby, results in imaging degrading, and engenders blurring imaging. The paper analyses a real process about image blurred as a result of object motion, reveals an intrinsical cause about image-degraded owing to object motion, and establishes blurring-model by which one dimension and two dimensions uniform velocity rectilinear motion result in image blurred abide.

为了有效地恢复运动模糊图像，从像素运动的角度分析了因运动造成的图像模糊的实际过程，并首先揭示了运动造成图像降质的内在原因，然后根据模糊图像像素间的关系建立了一维和二维由匀速直线运动所造成的模糊图像的模糊模型，并依据图像降质过程的逆过程推导出恢复模型。

First, the partial observability of target parameters when a single observation station moves with uniform velocity and the target moves with a uniform acceleration in the straight line is proved in theory.

首先在理论上证明了目标作匀加速直线运动，单观测站作匀速直线运动时的目标参数的部分可观测性。

In two c.s. moving uniformly, relative to each other, all laws of nature are exactly identical and there is no way of distinguishing absolute uniform motion.

在两个相对作匀速直线运动的坐标系中，所有的自然定律都是完全等同的，因而无法分辨出绝对的匀速直线运动。

What is meant by the statement that absolute and not only relative uniform motion exists? Simply that there exists one c.s.

如果说，不仅存在相对的匀速直线运动而且存在着绝对的匀速直线运动，这句话的意义是怎样的呢？

Results In lead poisoning group, the pathological changes in genital glands of mice were obtained; sperm count, linear movement sperm and live sperm rate decreased; the elevated motionless sperm, cacospermia and primary spermatocyte chromosome aberration rate were found. In Haierfu group, the pathological changes in genital glands of mice ameliated to different degree, sperm count, linear movement sperm and live sperm rate elevated, and motionless sperm, cacospermia and primary spermatocyte chromosome aberration rate decreased.

结果 醋酸铅染毒组雄性小鼠的生殖腺有不同程度的病理学改变，精子计数、直线运动精子数、活精子率下降，而静止不动精子数、精子畸形率和初级精母细胞染色体畸变率升高；海尔福治疗组小鼠的生殖腺病理学改变有不同程度的改善，精子计数、直线运动精子数、活精子率有所升高，而静止不动精子数、精子畸形率和初级精母细胞染色体畸变率有所降低。

Concurrently camp product :The automation mechanical device must each kind of translation series product, for example: The straight line guide rail, the guide screw strut, the shaft coupling, lock the nut, the straight line bearing, the knuckle bearing, the oil-retaining bearing and so on.

兼营产品：自动化机械设备所必须的各类直线运动系列产品，如：直线导轨、丝杠支撑、联轴器、锁紧螺母、直线轴承、关节轴承、含油轴承等。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。