直径的

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

The contents of this design are overall design of FXS900 combination separator and design of Cyclone Collector with Double Outlet for Dust . In the design of the separator, at first, calculate the air amount choose the air fan ,then confirm the diameters of the dust separator room and rotor.

在进行总体设计时，通过风量的计算选择风机，确定旋粉室直径与转子直径，再计算主轴的转速和选粉机的功率，选择电机和减速机。

Rhizome neck 5–10 cm, 1.8–2.5 cm in diam. Culms to 4 m, 1.5–2.5 cm in diam.; internodes terete, 15–17(–20) cm, initially slightly white powdery, longitudinal ribs absent; wall 2.5–5 mm thick; nodes with level or prominent supra-nodal ridge at branching nodes, slightly white powdery initially; sheath scar prominent, glabrous or initially slightly setose. Branches (3–)7–18 per node, deflexed.

根状茎颈5-10厘米，1.8-2.5厘米直径秆在4米，1.5-2.5厘米直径；节间圆柱状，15-17(-20)厘米，最初有点白色的敷粉，长度的肋骨缺席；壁2.5-5毫米厚；节具水平或突出超级节脊在分枝节，白色敷粉的稍最初；鞘有点最初结疤突出，无毛或。

The pupil diameter of different diopters changes greatly under different rays, and it is a very important parameter to measure the pupil diameter in different diopter under different rays before the refractive surgery.

不同屈光度在不同光线下瞳孔直径有很大的变化；不同屈光度在不同光线下的瞳孔直径是屈光手术前评估的一个重要参数。

In the experiment, two kinds of tubes with alternative diameters and material properties, and three kinds of flat-nosed cylindrical missiles with same length and various diameters are applied. Two classes including six operating modes are designed in the experiment.

在实验方面，本文采用了两种不同直径和材质的薄壁管试件以及三种长度相同，直径不同的平头弹体，设计了两大类六种工况下的实验。

With the development of the marine in the world, more and more emphasis was paid to the structure of large-diameter reinforced concrete cylinder.

随着世界上海运的发展，大直径薄壳圆筒结构形式日益受到重视，采用大直径圆筒结构直接插入地基土体的结构形式是近年来在我国发展起来的一种港口工程结构形式。

Though true aerosol particles range in diameter from a few nanometres to about one micrometre, the term is commonly used to refer to fog or cloud droplets and dust particles, which can have diameters of more than 100 micrometres.

真正的气溶胶微粒直径由数毫微米到1微米，此词特别常用于云或雾中的水滴和尘埃微粒，它们的直径都大于100微米。

Though true aerosol particles range in diameter from a few nanometres to about one micrometre, the term is commonly used to refer to fog or cloud droplets and dust particles, which can have diameter s of more than 100 micrometres.

真正的气溶胶微粒直径由数毫微米到1微米，此词特别常用于云或雾中的水滴和尘埃微粒，它们的直径都大于100微米。

Though true aerosol particle s range in diameter from a few nanometres to about one micrometre, the term is commonly used to refer to fog or cloud droplets and dust particle s, which can have diameters of more than 100 micrometres.

真正的气溶胶微粒直径由数毫微米到1微米，此词特别常用于云或雾中的水滴和尘埃微粒，它们的直径都大于100微米。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。