直径的

Different flow profiles were produced by using different ID of frits.

还观察到不同直径的筛板导致不同的流型。

Internodes shorter than 33 cm, not more than 2 cm in diam.; culms sparsely white powdery when young

节间短于33厘米，2厘米直径的不超过；白色敷粉的秆疏生幼时 9

The advantage of the swirling water jet breaking rock is the heavy breaking efficiency, large breaking area and less energy used to break rock per unite volume, so the swirling water jet can drill in a hole of a large diameter.

旋转射流破岩的优势在于破碎面积大、效率高、破岩比能低，因而旋转水射流能够钻出大直径的岩石孔眼。

This results in large-diameter runners being required which progressively length the moulding cycle and more scrap is producd.

这就要求大直径的流道从而延长了注塑周期并且产生较多的废料。

Bending angle about material augments along with laser power and laser light spot diameter augment, but bending angle about material minishes along with laser scan rate and material hardness augment.

随着激光功率和激光光斑直径的增加板材弯曲角度增大，但随着激光扫描速度和板材厚度的增加弯曲角度减小。

Motheds Fourty lumbar vertebras harvested from ten fresh mature goat cadavers were evenly assigned to one of five groups.

方法将40个成年新鲜山羊椎体，随机分为5组，每组8个，分别在椎体矢状面中点垂直矢状面方向，用不同直径的钻头横向钻通椎体造成缺损，并在材料试验机测试各椎体的强度和刚度。

A small band of newly licensed trappers hit the trail this week of pythons ...

第一段：犯了跟CORBA一样的错误，这里没有直径的意思。

Therefore a 2 new toroids were built, each employing two tubes together around a 21cm diameter plywood disk.

因此，1 2个新的螺旋管建成，各自雇用约1 21厘米直径的胶合板上两条管道在一起。

Different splicers could make different slings by changing one piece of inserting pin.

不同规格的机组只需更换一根插针就可完成不同直径的钢丝绳插套。

Quadruple hamstring constructs and femoral tunnel diameters were measured using 1 mm increment graft sizers.

用逐毫米增加的移植物测量计测量四股腘绳肌复合结构及股骨隧道直径的大小。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐