皱边

He frowned, and getting up, went over to the bookcase and took out a volume at hazard.

他皱皱眉头，站起身来，走到书架边随手抽了一本书。

A strip of frilled or closely pleated fabric used for trimming or decoration.

褶裥饰边：用于镶边或装饰的具有饰边或折皱的布条

All focussed their attention at the scene exhibited, a group of savage women in striped loincloths, squatted, blinking, suckling, frowning, sleeping amid a swarm of infants (there must have been quite a score of them) outside some primitive shanties of osier.

99大家都把注意力集中在出示给他们的图片上：一群未开化的妇女腰间缠着条纹布，蹲在柳条编成的原始窝棚前面，在成群的娃娃簇拥下，边眨巴眼睛，让娃娃叼着乳房，边皱起眉头，打着盹儿。

Emperor sees an edge by the side of Bede pursy brows, say to that fellow: I did not see you did the thing with particularly good what, but you also had not done what evildoing.

圣彼德边看边皱起眉头，对那家伙说：我没看到你做了什么特别好的事情，但你也没做过什么坏事。

These two defects were suppressed when polyurethane elastic cushions and steel paddings were used between the titanium alloy retiary sheet and the press punch with the blankholder device in the forming technology mode, and the 3D curved surface of prosthesis with good quality can be acquired.

模拟结果表明：采用前两种成形工艺得到的钛合金颅骨修复体表面出现压痕或起皱缺陷，采用在基本体和钛合金网板之间放置聚氨酯弹性垫和钢质垫板并使用压边圈这种成形工艺时，可以抑制压痕和起皱的产生，获得良好的成形效果。

The greatest variation takes place in the volume contractive rate of the heartwood, collapse factor and collapse depth of the sapwood.

心材的体积收缩率、边交界材的皱缩因子和皱缩深度变化最大。

An apparatus to adjust BHF on single-acting hydromechanical press was designed by the author based on the BHF model Experimental results showed that this device was useful in avoiding wrinkling during drawing.

依据所建立的压边力模型，设计了单动油压机的压边力调节装置，实验证明该装置对于防止内皱有重要意义。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果展开平板在压边圈面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈表面间的平衡块；压边圈的变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

褶皱起因于不充分的拉伸或失去控制的压缩变形。如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

Lotus Leaf contexts it business card printing and membership card making misregister or wrinkling, see double fault, the most common is the business card printing and membership card making wrinkle.

荷叶边也容易造成制卡和会员卡制作起皱、套印不准或重影故障，最常见就是制卡和会员卡制作起皱故障。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。