电镀的

The environmental agreeableness of galvanic sludge is investigeted in the laboratory at the Institute of Metallurgy,Technical University of Berlin.

按照环保的标准和要求，柏林工业大学冶金研究所对不同种类、成分的电镀泥进行了试验室研究，对含金属的废电镀泥进行直接和经火法预处理后的浸取溶出。

Cement and silver sand are used as the basis materials for solidifying galvanized sludge containing heavy metals such as Ni,Cr and Cu,the lixivium test to solidified matter shows that the effect of solidifying galvanized sludge with cement is good.

采用水泥和细砂作固化基材处理含Ni、Cr、Cu等重金属的电镀污泥，对固化块的浸出试验表明：水泥固化该电镀污泥效果良好，固化过程中加入适当的螯合剂KS-3，可以提高固化效果，并对固化块在不同pH浸取剂下的重金属浸出浓度进行了研究。

"It has valence 2 or 4 in compounds, including stannous chloride (used in tin galvanizing and manufacturing polymers and dyes), stannous oxide (used to make tin salt s for chemical reagents and plating), stannous fluoride (used as an anticavity ingredient in toothpastes), stannic chloride (a stabilizer for perfumes and a source of other tin salt s), and stannic oxide (a catalyst and a polishing powder for steel)."

在化合物中的原子价为2和4。化合物包括氯化亚锡(用于电镀锡以及制造聚合物和染料)、氧化亚锡(制备化学试剂和电镀用的锡盐)、氟化亚锡、氯化锡(香水的稳定剂以及其它锡盐的原料)以及氧化锡(催化剂以及钢材的拋光粉)。

A kind of high speed sulphamate nickel-based electrolyte is chosen as basal electrolyte, the influences of plating process parameters on the micro-hardness of the nickel deposit have been studied by orthogonal experiments. It is concluded that the main influence factors on the micro-hardness of the nickel deposit are sulphamate concentration and electrolyte temperature, the deposition rate and quality in single-pulse mode are higher than that in DC power and double-pulse mode.

选择以氨磺酸型高速镀镍液作为基础镀液，通过正交试验研究了电镀工艺规范对镀层显微硬度的影响关系，试验结果表明：镀液主盐氨基磺酸镍浓度和镀液温度是影响镀层硬度的显著因素，单脉冲供电模式下的电镀沉积速率和镀层质量优于直流和双脉冲模式。

The new main features of the Serpent 720 '08 are the a new black anodised chassis plate, front brass plate, new 0 and 1mm offset steering blocks, an aluminium radio plate X bracket and single piece orange anodised engine mount.

新的主要特点该蛇720 '08是一个新的黑色电镀底盘板，前线黄铜板，新的零和一毫米抵销督导大厦，一铝电台板x托架和单件橙色电镀引擎挂载。

Four key technologies were discussed for the remanufacturing engineering of electroplated diamond tool, which were green recycling, selection classification, design of diamond tools with remanufacturing ability, and evaluation of remanufacturing ability.

论文阐述了电镀金刚石工具再制造工程面临的4项关键技术问题，即电镀金刚石工具的绿色回收技术，分选技术，工具的再制造性设计以及再制造性评价。

Technology of galvanoceramic is a process of fabricating ceramometal restorations utilizing 99.9% pure gold copings by electroforming techniques, electrodepositing a metal onto a suitable substrate in specific electroforming apparatus.

金沉积烤瓷修复技术是指通过专用的电镀仪，利用电铸原理，在模型上电镀出含99.9％纯金的金沉积冠，然后在其表面进行烤瓷的修复技术。

The effects of electroplated Ni layer and electroless plated Ni-P layer on the diffusion behavior in Sn-Ag/Cu solder joint were studied. The results by EPMA analysis showed that the electroless plated Ni-P layer acted as a good diffusion barrier between Sn-Ag solder and Cu substrate. However, the electroplated Ni layer can not hinder the inter-diffusion and reaction between molten Sn-Ag solder and Cu substrate when reflowing, and there was a layer of IMC (Cu6Sn5) at interface of Sn-Ag/C u solder joint.

摘 要：研究了电镀Ni层和化学镀Ni-P合金层对Sn-Ag/Cu焊点扩散行为的影响，电子探针分析表明：化学镀Ni-P合金层能很好地阻止Sn-Ag/Cu焊点在焊接过程中的Cu，Sn互扩散和相互反应；而电镀Ni层则不能阻止Sn-Ag/Cu焊点在焊接过程中的Cu，Sn互扩散和相互反应，界面反应产物仍以Cu6Sn5为主。

The company introduces world-levelhigh-speed precision punch,high-speed continuous galvanization technology and high-speed mould punching technology,etc from America and Taiwan.

公司以人为本，以品质为中心，拥有优秀的工程技术人才以及大专以上学历的管理人才，从美国、日本、台湾引进高速精密冲床、高速连续电镀线和先进的检测设备，高速连续电镀技术、高速模具冲压技术等处于国际先进水平。

Thus the process for the electroplating of aluminum on NdFeB permanent magnetic material in the molten salt electrolyte at room temperature was investigated.

探讨了NdFeB永磁材料在室温熔盐中电镀铝的可行性、熔盐配比和芳香化合物对电镀铝层组织形态的影响，同时对镀层形成的机理进行了初步探讨。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。