电镀层

When electroplating zinc, zincate zinc plating was carried out at 30℃by 3.0 A.dm~(-2) for 20 min, highly compact zinc coating can be obtained, but the additives play an important role.

焦磷酸盐镀锌时，电流密度在1.0~3.0 A.dm~(-2)下电镀时间超过10 min，镀层达到较致密的镀层。

If throwing of metalization is the better,Than dog boning plating coming to pass is the least or it is more,Letterpress will search diversified factor that willk work on throwing from plating metalization thickness that it is work onfirst-degree currents and second-degrren current sand electricity chemical.

本文从电化学过程，从镀层厚度分布受一级和二级电流分布入手，探究影响分散性的各种因素，优化电镀工艺参数，从而教好克服狗骨镀层现象。

The electrodeposited coating system used on plastics substrates always consists of an initial thick copper layer.

用于塑料的电镀涂层体系总是包含一层厚的起始铜层。

Tinned sheet is cold rolled sheet whose surface is electroplated with a layer of uniform and dense tin.

0前言镀锡板是在冷轧板的表面电镀一层均匀致密的锡层。

Tinned sheet is cold rolled sheet whose surface is electroplated with a layer of uniform and dense tin.

镀锡板就是在冷轧板的表面电镀一层均匀致密的锡层。

The process for Zn-Ni alloy electroplating in weak acid bath was investigated. The brighteners suitable for this system were developed. And the effects of bath compositions and process conditions on the composition of deposits were studied.

研究了弱酸性氯化钾－乙酸按体系电镀Zn-Ni合金工艺，开发了适于本体系的光亮剂，深入探讨了镀液组成及工艺条件对镀层组成的影响，获得全光亮Zn-Ni合金镀层的最佳工艺。

The performance parameters of the bath and Cr coating were measured.

测定了镀液及镀层的性能，结果表明，该体系具有良好的稳定性，在10～20A/dm2光亮电镀范围内，分散能力为70%～84%，覆盖能力为100%，所得镀层颜色白亮，耐蚀性优良，综合性能与国外同类产品相当。

In addition, the repair method can also be filled tree holes, stuffing is best to use small gravel and cement mixture to be compacted filler, filler to strengthen the connection with the xylem, inside the cave can be a number of electroplating nails nails, holes dug in on both sides 4 centimeters deep groove at the bottom of filler from the start, each 20-25 cm for the layer, using linoleum separated from each floor should be inclined slightly outward to facilitate drainage, the edge should not exceed xylem, so that cambium in the formation of callus on it.

另外，也可用填充法修补树洞，填充物最好用小石砾和水泥的混合物，填充物必须压实，为加强填料与木质部的连接，洞内可钉若干电镀铁钉，洞口内两侧挖4厘米深的凹槽，填充物从底部开始，每20厘米至25厘米为一层，用油毡隔开，每层都要向外略斜，以利排水，边缘应不超过木质部，使形成层能在它上面形成愈伤组织。

Electrochemical properties of electrodeposited Cu/Co multilayers were investigated by potentiodynamic curve and electrochemical impedance spectroscope. X-ray diffraction and scanning electron microscopy were used to study the sample structure and morphology.

中文摘要本研究利用准稳态动电位扫瞄法、电化学交流阻抗法研究电镀铜钴多层膜的电化学特性，并利用X光绕射仪和扫瞄式电子显微镜研究镀层的结晶结构和形态。

However, in the business card printing and membership card in case of making paper out of the dirt and friction are suites-rolling up dew producing copper, dirt, diabetes'mellitus to marketizing to get rid of CR rolling dirt broken, you need to start from the dirty yellow amiodaron potassium in addition to, and then use special equipment electrized chromeplating, more time-consuming.

但在制卡和会员卡制息历程洋如逢纸弛掉下的砂粒摩擦，不常不兵版面铬层轧碎后露铜，爆发感脂上不净弊病，给打消镀铬层轧碎上不净出格便当，需不后用黄胺酸钾不兴不净，然后再用兼用摆设通电镀铬，较不省工夫。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。