电镀层

The use of acid-base and humid environment on the corrosion of metal plating layer to test the corrosion resistance.

利用酸碱和湿热环境对金属的腐蚀性来测试电镀层的抗腐蚀能力。

Lead in the plating layer of high voltage diodes on the basis of a zinc borate glass body.

以硼酸锌玻璃体为基础的高压二极管的电镀层的铅。2009/443/EC

Lead in the plating layer of high voltage diodes on the basis of azinc borate glass body.

以硼酸锌玻璃体为基础的高压二极体的电镀层的铅含量。

This method is applied to determine the content of Cu and Mn in the electroplating solution and electroplated layer.

101%。其方法适用于电镀液和电镀层中Cu和Mn的测定。

As for glass product, leather, printing board, stone, plastic, aggregate and the process of galvanizer, they are of high efficiency.

对于玻璃制品、皮革、印刷板、石料、塑料、骨料及电镀层的加工均有良好的效果。

The abilities of corrsion resistance of many kinds of accessories after different surface disposed and dealed with the BH-102 hydrophobe agent had been studied.

为防止金属零件腐蚀，通常在一些零件表面进行处理(如电镀层、转化膜层等)，但是有些膜层存在着孔隙等缺陷，环境中的水分子会沿着孔隙扩散到基体而引起材料腐蚀。

The morphology and microstructure of Ni-La2O3 codeposited films were studied by means of metallograph, electron probe microanalyzer ,transmission electron microscope and high resolutionelf3ctroli microscope.

用金相、电子探针、透射电镜及高分辨电子显微镜对Ni－La2O3复合电镀层的表面形貌及LaO3质点在镀层中的存在情况进行了研究。

The result shows that the corrosion resistance of nano-composite electrodeposits prepared under pulse current condition is obviously better than that under o...

结果表明，在脉冲条件下所制备纳米复合电镀层的耐蚀性明显优于其它电镀层，其原因是电镀层中复合有适量的纳米ZrO2颗粒以及脉冲电沉积工艺本身所致。

A Ni-ZrO_2 nano-composite were prepared by electrodeposition.The corrosion resistance of the Ni-ZrO_2 nano-composite electrodeposits in 10%HCl and 10%H_2SO_4 solutions respectively was studied by massloss measurement.SEM was used to observe the morphology of various electrodeposits after corrosion test,and the relevant corrosion mechanism was discussed.

采用电镀工艺制备了纯镍电镀层和Ni-ZrO2纳米复合电镀层，对纯镍电镀层和Ni-ZrO2纳米复合电镀层分别在10%HCl和10%H2SO4溶液中的耐蚀性进行了对比研究，用SEM对各种电镀层腐蚀后的表面形貌进行了观察。

Then we can pre-empt problems by building the mold with special inserts to rotate the flows into double-stacked hot-runner manifolds through sequenced valve gates into pressure-monitored cavities fabricatedfrom a myriad of steels coated with exotic super-hard, lubricious, rust-proof platings applied with little heat and thinner than air.

然后，我们捷足先登：用特殊的嵌件构建模具，使料流旋转进入双层结构的热流道，再通过顺序浇口的开启注入到压力监控的模腔，这些模腔是用涂覆着超硬的、润滑的、防锈的电镀层制造的，这些电镀层绝热效果好，比空气分子还薄。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。