电镀

Electroplated diamond wire saw is a kind of linearity superhard material tool, which is prepared by electroplating a layer metal deposit on metal wire and concreting diamond in the deposited metal.

电镀金刚石线锯是用电镀的方法在金属丝上沉积一层金属，并在沉积的金属内固结金刚石磨料制成的一种线性超硬材料工具。

Result show that compounding with different current density and time will effectively enhance the throwing power and efficiency of high aspect ratio through-hole plating.

结果表明，改变采用不同电流密度分段电镀可有效提高镀通性和电镀效率，且孔铜可靠性良好。

In this paper, we study effect of current density on throwing power and elongation, then investigate throwing power of high aspect ratio through-hole under different plating parameter, and research the reliability of PTH.

本文研究了不同电流密度下高厚径比镀通性及镀层延展性的变化趋势，在设备和药水条件基本固定的情况下，考察不同电镀参数组合对高厚径比通孔电镀的效果，并对不同参数下的孔铜作热应力测试对比。

The results show that compared with Cr coating, Cr plating possesses many advantages, such as high efficiency, high throwing power, high covering power, low toxicity. However, maintenance of the bath is complex and frequent.

结果表明：与六价铬电镀工艺相比，三价铬电镀工艺具有低毒性、常温施镀、电流效率高、生产效率高、镀层性能好等优点，但其调整维护相对频繁、复杂。

The company was established in 2001, covers an area of 16,000 square meters, are set production, sale and service of professional manufacturers, professional production·, chemical pure, pure electronics, industrial pure content specifications such as sulfuric acid, nitric acid, hydrochloric acid, sodium hydroxide, hydrogen peroxide, ammonia and other chemical raw materials and chemical reagents, as well as multi-layer circuit boards, flexible circuits board, semiconductor, electronic plating, chemical plating, wastewater treatment and a variety of electronic device manufacturers to provide supporting services.

公司成立于2001年，占地面积16000平方米，是集生产、销售、服务于一体的专业型厂商，专业生产分析纯、化学纯、电子纯、工业纯等各种规格含量的硫酸、硝酸、盐酸、氢氧化钠、双氧水、氨水等各种化工原料及化学试剂，并为多层电路板、软性电路板、半导体、电子电镀、化学电镀、废水处理及各种电子器件生产厂商提供配套服务。

Our professional committed to the linked to a plating, Shen copper basket, and the basket, the nickel basket,-socket board, socket board - Plating and other supplies.

本厂专业致力于电镀用挂具，沉铜篮、黑化篮、化镍金篮，插板架，插板架等电镀用品。

Thus the process for the electroplating of aluminum on NdFeB permanent magnetic material in the molten salt electrolyte at room temperature was investigated.

探讨了NdFeB永磁材料在室温熔盐中电镀铝的可行性、熔盐配比和芳香化合物对电镀铝层组织形态的影响，同时对镀层形成的机理进行了初步探讨。

By studying the effects of mole rate of AlCl3-MEIC and fragrant chemical compound and dewater agent, electroplating aluminium bath of AlCl3-MEIC room temperature melt salt was prepared, and silvery white metallic luster , pre-pressing smooth aluminium layer is electroplated on NdFeB magnet from this solution.

4研究了AlCl_3和MEIC的摩尔比、芳香化合物及除水剂对室温熔盐电镀的影响，制备了AlCl_3-MEIC室温熔盐电沉积铝溶液，并从该溶液中电镀出了具有银白色金属光泽、致密光滑的铝镀层。

In electroplating aluminum on NdFeB magnet with use of AlCl3-MEIC room temperature melt salt bath,said magnet is activated to improve deposit adhesion by carrying out.before plating,electrolysis on said magnet.and plating process was described as below:Toasting and degreasing ?Sand blasting Drying Electricity activating?ElectroplatingSolvent washing Water washing Drying

5利用室温熔盐电解质作活化液对钕铁硼磁体进行电活化处理，可以提高基体和镀层的结合力，并提出如F电镀工艺流程：烘烤除油→喷砂除锈→干燥→电活化→电镀→溶剂洗→水洗→干燥

Finally arranges and the plan plating department horizontal plan designing and the plan electroplating bath tank the platoon windsail and so on the non- standard equipment detail as well as craft card certain.

最后布置并绘制电镀车间平面图，设计并绘制电镀槽、排风罩等非标准设备详图以及工艺卡若干张。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。