电铸

Using nickel aminosulfonic bath as a study system of electroform ing and by adding cobalt aminosulfonic,the internal stress,composition,hardness and tensile strength of the electroform ed nickel-cobalt deposit were tested.

采用氨基磺酸镍镀液作为电铸的研究体系，并在镀液中加入氨基磺酸钴，对镍钴合金电铸层的内应力、组成、硬度、抗拉强度等进行了测试。

Suzhou Yong Jin Precision Die Casting plant, electroform processing system mainly used for ordinary law-not surface processing requirements and narrow and difficult polishing of the mold inserts.

苏州勇进精密电铸模具厂，电铸加工主要用于普通制模法无法加工之表面要求和狭而不易抛光之模具镶件。

In this thesis, a micro-featured surface was used as a carrier and coated a thickness of 1500 angstrom ITO to form an electric conductive film for further electroform.

本研究乃利用现已成熟的电铸技术，在微特徵光阻表面镀上一层厚为1500的铟锡氧化膜(Indium Tin Oxide，ITO)，让微特徵表面形成导电膜，以利微特徵结构进行电铸。

Dongguan Run hui Precision Die Casting plant, electroform processing system mainly used for ordinary law-not surface processing requirements and narrow and difficult polishing of the mold inserts.

东莞润辉精密电铸模具厂，电铸加工主要用于普通制模法无法加工之表面要求和狭而不易抛光之模具镶件。

Such as audio panels, knobs, phone panels, battery lid, mp3 keys, cell phone navigation button, the lights, cosmetics lid, optical lenses , electroforming signs, Penstock, remote control car keys, reflective panels, lightguide plate, electroform nickel, and other signs.

如音响面板、旋钮、手机面板、电池盒盖、mp3按键、手机导航键、车灯、化妆品盒盖、光学镜片、电铸标牌、笔杆、汽车遥控按键，反光板，导光板，电铸镍标牌等。

In order to improve the micro electroforming quality of a microstructure,the characteristics of the micro electroforming process were discussed systematically and the properties of the electric field and flow field were analyzed.

在分析微细电铸的电场与流场特性的基础上，深入研究了铸层厚度的不均匀现象及搅拌方式和电流密度对微细电铸质量的影响。

Initial experimental study is done about electroforming process and fluid model is set up. Electric field distribution is found to be nearly normal.

在此基础上，对射流电铸成型工艺进行了初步的实验探讨，建立了射流电铸的流体模型，并发现电场的分布为近似正态分布，它与电压和流场密切相关。

On the foundation of manufacturing numerical control jet electroforming machine, In this thesis, for numerical control jet electroforming, the research presented creative and conclusion works as follows

本文在研制和开发数控喷射电铸机床的基础上，对数控喷射电铸进行了以下几个方面的研究并做出了一定的创新

The relationship between coating microstructure and electromagnetic properties of electroformed Ni-Fe alloy s was studied.

研究了电铸镍铁合金制备过程中工艺条件对电铸层成分的影响，获得含铁质量分数20%电铸层的最佳工艺条件为镀液硫酸亚铁含量6g/L、pH值2.5、温度55℃、电流密度3.5A/ dm~2；讨论了镀层形貌及电磁性能的变化关系。

In this paper, arc spray molding technology was used to manufacture large size sheet forming mold successfully.

电铸与电弧喷涂相结合的模具制造方法提高了模具的性能，通过优化电铸工艺，电铸Ni-Co合金层硬度可达到HV600。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。