电流变换器

In the light of the trapezoidal back electromotive force and square phase current of brushless DC motor,a novel strategy of matrix converter driving BLDCM is presented in this paper.

针对无刷直流电机反电势为梯形波、相电流为方波的特点，提出一种用于驱动无刷直流电机的矩阵变换器的控制策略。

Flyback converter based on peak current-control technique is discussed in this article.

本文对基于峰值电流控制技术反激变换器进行了研究。

Compared to the other second-side rectifier, it is concluded that the full-wave Rectifier is well adapted to the Low-voltage High-current DC-DC converter.

论文通过对全波整流输出电路与其他副边整流电路的比较，得出采用全波整流电路特别适合隔离型低压、大电流输出的DC／DC变换器的结论。

This paper presents analysis in detail and designs a Zero-Current-Switched Quasi-Resonant SEPIC converter in full-wave mode.

该文详细分析和设计了一种实现零电流软开关的全波模式下的准谐振SEPIC变换器，并利用Matlab6。

The method combing harmonic linearization and integral time absolute error optimal control to realize the PWM converters' optimal control is proposed according to the hysteresis current control's characteristics.

根据滞环电流控制的特点，提出了将谐波线性化方法与ITAE优化控制律相结合的方法，以实现对PWM变换器的优化控制。

The thesis contains five chapters. The first chapter summarizes the development and research of switched reluctance drive, discusses the main research direction, and explains the main work in this paper. In chapter 2, hardware system which includes the design of power converter and various control circuit is discussed. TMS320LF2407 DSP is used to design the hardware circuits of SRM control system, and design details including the current detection, position sensing, fault protection, speed detecting, keyboard and display etc. are provided. Because of the full use of the abundant peripheral resources of DSP, it comes to the aim simplifying the circuit structure and heightening the reliability. In chapter 3, the application of neural network on SRM control system is introduced, a new the application of neural network and the method of sampling is proposed and a simulation system based on Matlab/Simulink is established. Chapter 4 discusses the routine designing issue. Because the modularized programming method is adopted, and multi-interrupt processing technique is used, operation efficiency of the control software is highly raised. At last, the foregoing SRM control system is tested. Speed adjustment is realized, and other targets on the research and design of SRM control system are reached, which establishes a good foundation for further research.

本文共分五章，第一章概述了开关磁阻电机调速系统(Switched Reluctance Drive，简称SRD)及其发展和研究现状，论述了其主要研究方向，并说明了本文的主要工作；接下来的一章主要讨论了SRM的硬件系统，主要包括功率变换器的设计和各种控制电路的设计，本文以TMS320LF2407为核心设计了开关磁阻电机控制系统硬件电路，给出了包括电流检测、位置检测、故障保护、测速电路及键盘和显示电路等部分电路的详细设计，充分利用了DSP的丰富外设资源，达到了简化电路结构、提高运行可靠性的目的；第三章介绍了人工神经网络在开关磁阻电机控制系统中的应用，提出了一种新的应用方式(利用GPFN神经网络调节PI参数)以及如何采取样本，搭建了基于Matlab/Simulink的仿真系统；在第四章中，讨论了开关磁阻电机控制软件的设计，采用模块化编程方法，采用基于多中断的控制程序，提高了控制软件的效率；最后，对所设计的开关磁阻电机控制系统进行了实验，实现了电机调速，达到了开关磁阻电机控制系统研究和设计的预期目标，为更近一步研究打下了基础。

As a result,conventional switched capacitor have been limited to be used with a very small output current.

因此，传统的开关电容变换器只能使用在输出电流很小的场合。

In the thesis, the space vector modulation of MC can be synthesized by fictitious rectifier and fictitious inverter. Two space vector control strategies of MC, which combines output line voltage space vector modulation and input phase current space vector modulation, is adopted.

本文采用输出线电压空间矢量调制和输入相电流空间矢量调制相结合的双空间矢量调制策略，对虚拟整流器和虚拟逆变器的空间矢量分别进行了分析，然后将二者综合得到矩阵变换器的调制方法。

A class of piecewise smooth maps with two border and three zones is derived to describe the dynamics of a current-programmed Buck converter operating in a discontinuous mode.

本文以不连续导通模式下的电流反馈型Buck变换器为例，推导出两个边界三段形式的分段光滑系统的离散映射模型。

In Chapter 3,Stroboscopic maps are derived to describe precisely the nonlinear dynamical characteristics of Boost PFC converters under peak-current control mode.

第三章推导出了一组频闪映射方程来精确描述峰值电流控制型Boost PFC变换器的非线性动力学特性。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。