电流

The adhesion of the obtained alloy coating to substrate is very good, the cathode current efficiency of the electrolyte is up to 90 percent.

合金镀层与基体结合力好，镀液的阴极电流效率可达到90%以上，光亮电流密度范围宽，镀液稳定，易维护。

It is of great significance for main economic technical indexes to improve current efficiency, unit power consumption and reducing unit output ect to choose density of cathode current in designing electrolysis tank.

在电解槽型的设计过程中，如何合理选择阴极电流密度，对提高熔盐电解的电流效率、单位时间产量，降低单位电耗等主要技术经济指标具有十分重要的现实意义。

L Applied battery range is wide: charge current can be set between 10% to rating, can't be influenced by the change of input current and voltage, keep constant in the process of constant charge and no need hand adjustment.

l 适用电池范围广：充电电流可在10%-额定值内任意设定，且不受输入交流电压变化的影响，在恒流充电期间电流维持不变，无需人为再调整。

L Applied battery range is wide: charge current can be set between 10% to rating, cant be influenced by the change of input current and voltage, keep constant in the process of constant charge and no need hand adjustment.

l 适用电池范围广：充电电流可在10%-额定值内任意设定，且不受输入交流电压变化的影响，在恒流充电期间电流维持不变，无需人为再调整。

Whole cell patch clamp technique was used to investigate the effect of sinomenine on sodium current and L-type callium in isolated guinea pig ventricular myocytes.

应用膜片钳全细胞记录技术研究青藤碱对酶解分离的豚鼠单个心室肌细胞膜钠离子电流、L型钙电流的影响。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Fig. 15 Influence of the drain current continuous conduction mode

图15漏极电流的影响（连续电感电流模式，6.8欧姆栅极

When spark switch closes,an electric arc forms between the electrode,and current conduction begins.

当气体火花开关闭合时，开关电极之间会产生强烈的大电流电弧，电极内部开始有电流流动。

Fig. 15 Influence of the drain current continuous conduction mode, Rgate="6".8 Ohm, measured

图15漏极电流的影响（连续电感电流模式，6.8欧姆栅极驱动电阻

They go to town. Would you just ask them?

他们在城里你能问他们吗？

Ossein pretreated for a2 weeks period exhibited the maximum% yield incase of bone gelatin, while the yield from intact skin was higher than that realized incase of de-scaled skin.

预处理时间达2星期的骨胶原表现出最高的骨明胶百分产量，然而从未处理鱼皮中得到的产率比去鳞的鱼皮得到的要高。