电容耦合

The capacitance bleeder is used in capacitive voltage transformer as bleeder, concurrently as coupling capacitor.

电容分压器用于电容式电压互感器中，做分压器用并兼作耦合电容器使用。

This new layout design can minimize the voltage drop across interconnects and can prevent the capacitive coupling to devices.

此一新型的布局设计能将内连线上的电压降减少至最低，并能防止元件遭受到电容性耦合效应。

In the application, we discuss the two common phenomenon of the meander delay line:(1) speed-up of the signal due to inductive/capacitive coupling between coupled lines and(2) the ladder wave distortion.

在应用方面，本论文探讨下列两种蜿蜒型延迟线常见的现象：（1）由耦合电感及电容引起的输出超前现象，（2）阶梯波失真现象。

The control device 7 is coupled to a load and/or a capacitive buffer.

控制设备7耦合到负载和／或电容缓冲器。

Forcoupling capacitance method, it needs to measure the effective value of the feeler search.

耦合电容法是根据动态电荷分布和电容分压原理提出的。

S1 is then changed to position 1. The voltage stored on C1 is inserted between the output and inverting input of the amplifier and the output of the amplifier changes by VIN to maintain the amplifier input at the input offset voltage. The output then changes from (VOS + IbiasR2) to (VIN + IbiasR2) as S1 is changed from position 2 to position 1. Amplifier bias current is supplied through R2 from the output of the amplifier or from C2 when S1 is in position 2 and position 1 respectively. R3 serves to reduce the offset at the amplifier output if the amplifier must have maximum linear range or if it is desired to DC couple the amplifier.

接着 S1 拨到位置 1，使 C1 的电压加在放大器的输出端和反相输入端之间，(由于电容端电压不能突变，所以)输出端的电压将产生大小等于 VIN 的变化，使放大器输入端维持输入失调电压，即当开关 S1 从位置 2 拨到位置 1 时，输出端电压将从(VOS + IbiasR2)变为(VIN + IbiasR2)。S1 处于位置 2 时，放大器的偏置电流是由输出端经电阻 R2 提供的，当 S1 转向位置 1 时则由 C2 提供。R3 的作用是降低输出失调电压，如果要求放大器具有最大的线性范围，或者采用直流耦合，就应该使用该电容。

These antennas can cover GSM900/DCS/PCS/UMTS operation. In the chapter 2, the antenna is designed based on the concept of monopole antenna. Furthermore, the antenna structure have two radiant paths and coupled each other at tail end to do impedance matching. In addition, to raise distance between radiation plane and ground will avoid capacitative effect effectually. In the chapter 3, the antenna is designed based on the concept of planar inverted-F antenna. Furthermore, that the antenna structure have two radiant paths and coupled each other at tail end to do impedance matching is similar to chapter 2. But there is a difference in them. We can choose the short position to change input impedance at this structure. In the chapter 4, the antenna is designed based on the concept of planar inverted-F antenna which takes coupled-fed. It will produce the first mode and high-order mode near the frequency, 900MHz. The feature of this type is to reduce the volume effectually. This antenna can not only cover GSM900/DCS/PCS/UMTS operation but maintain good radiation efficiency. Finally, we will compare three antennas, and develop procedure with industrial view, and propose the prospect of the GSM/GPRS antenna in PND, as a conclusion.

在第二章中，我们使用单极天线设计概念，使用双路径架构并於末端耦合来对天线阻抗做匹配，产生涵盖GSM900/DCS/PCS/UMTS四频操作频带，并提高与接地面的辐射高度，以避免电容效应，使天线具有良好的辐射特性；在第三章中，使用倒F形天线设计概念，使用双路径架构於末端耦合，并於辐射臂上采取适当接地点电感效应作输入阻抗匹配，达成涵盖GSM900/DCS/PCS/UMTS系统的四个操作频带；在第四章中，采用倒F形架构并使用耦合馈入方式，使得长辐射金属臂在低频900 MHz附近产生共振，产生低频基频模态及高阶模态，以达成宽频及频宽涵盖GSM900/DCS/PCS/UMTS频带操作，并有效缩减使用体积；最后，分别比较此三种架构的优缺点，再加以业界角度来思考，研发产品天线的流程及思考方向，以及天线应用於可携式导航装置中未来的展望作为本论文的总结。

It is important that how to ascertained the coupling coefficient and selected the coupling capacitor ,in the design of the capacitor coupling circuit.

因此，耦合系数的确定与耦合电容的选择是该电路设计中的一个重要问题。

Voltage Source and Current Source, Thevenin Theory, Trouble Shooting, Characteristic Curve of Diode, Diode Models, Rectifier Circuits, Input Filtering Capacitor, Voltage Multiplier Circuits, Limiter and Clipper Circuits, DC Clampers and Peak-to-peak Detectors, Zener Diode, Zener Diode Rectifier, Photoelectric Devices, Collector-Emitter Junction, Transistor Characteristics of common-emitter, Base Bias, LED Dirver, Establishing a Stable Q-point, PNP Transistor Biasing, Transistor Biasing, Coupling and By-Pass Capacitors, AC Emitter Resistance, Common-Emitter Amplifier, Other Common-Emitter Amplifiers, Cascaded Common-Emitter Amplifiers, AC Load Line, Emitter Follower, Class B Push-pull Amplifiers, JFET Characteristic Curve, JFET Biasing, JFET Amplifier, VMOS Circuit, Differential Amplifier, Operational Amplifier, Non-inverting Feedback, Negative Feedback.

电子学实验( S0704)(1，1)/应用电子学实验( S0472)(1，1)电压源和电流源、戴维宁定理、故障排除、二极体特性曲线、二极体近似模型、整流电路、电容-输入型滤波器、倍压电路、限制器电路和峰值检测电路、直流定位器与峰对峰检测器、齐纳二极体、齐纳二极体整流器、光电元件、集射极接面、集极特性曲线、基极偏压、LED驱动器、建立一个稳定的工作点 Q 、 PNP 电晶体偏压、电晶体偏压、耦合及旁路电容、交流射极电阻、共射极放大器、其他 CE 放大器、串接共射极放大器、交流负载线、射极随耦器、 B 类推挽式放大器、 JFET 特性曲线、 JFET 偏压、 JFET 放大器、 VMOS 电路、差动放大器、运算放大器、非反向电压回授、负回授。

The shielded rectangular cross section slab line with cylindrical inner conductors is of great importance to microwave engineering and design.

在具有圆柱内导体的叉指滤波器和梳状滤波器工程设计中，对屏蔽矩形板线特性阻抗的计算至关重要，只有通过计算，才能确定滤波器中各导体的自电容和耦合电容值。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。