电子显微镜

The surface morphology of hair root and hair tail were analyzed by Scanning Electron Microscope.

采用微观摩擦磨损试验机对受损、干性和油性头发的摩擦系数及其发根和发稍的摩擦系数进行测试；通过扫描电子显微镜分析3种不同发质头发发根和发梢的表面形貌。

With the help of scanning electronic microscope, mild pressure treatment had obvious effect on the morphology of yeast Saf.

用扫描电子显微镜观察发现，温和压力处理对微生物细胞形态有显著影响。

By means of the scanning electron microscope and the Shore sclerometer, the microstructure and the Shore hardness of the materials were analyzed.

本文采用扫描电子显微镜、肖氏硬度计对碳/碳复合材料的表面微观形貌及显微硬度进行观察和测定。

We will look at two studies that address the 3-dimensional conformation of the native prion protein and the infectious scrapie state using cryoEM and X-ray crystallography.

我们将探讨两个分别使用低温电子显微镜和X射线结晶法阐明了自然状态下的朊蛋白和传染性的瘙痒病状态下的朊蛋白的三维构象的研究。

By means of strictly controlled sample preparation and various measurements of XRD, magnetic properties, XPS, Seebeck effect and electron microscopy, the effect of doping concentration and doping type on the phase separation is systematically investigated.

X 射线分析、磁测量、 XPS 分析、热电势测量、电子显微镜分析等实验手段，对掺杂浓度、掺杂质类型对相分离的影响作了较系统的研究。

X-ray diffraction was used to analyze the crystal structure and the field-emission scanning electron microscopy inspected the surface and cross-sectional morphology. X-ray photoelectron spectroscopy is used to determine the film composition. The optical transmittance, electric resistance, Hall Effect, and Seebeck coefficient were measured. It was found in XRD patterns that all samples possess In2O3 structure.

在特性量测方面，分别以X光绕射分析其晶体结构，场发射扫瞄式电子显微镜分析其表面及断面型态，以X光电子能谱分析仪分析薄膜成份，并搭配光穿透率、电阻率、霍尔效应及Seebeck系数等特性分析，探讨经热处理之后薄膜的热电特性变化。

Synthesis of silver selenide quantum dots using room temperature conversion method has been investigated.

本文采用室温转化法、分别用乙二胺与氨水做模板合成硒化银量子点，对合成的硒化银样品进行了 X-射线衍射分析，并在透射电子显微镜下研究了模板对合成硒化银形态的影响

The self-repairing performance and mechanism of nano-copper additive was analyzed by SEM and nano-test apparatus.

利用扫描电子显微镜和纳米压痕仪分析纳米铜添加剂的自修复性能和机理。

The phase composition and microstructure of the samples were characterized by XRD and SEM.

用X射线衍射和扫描电子显微镜分析了材料的物相组成和显微结构。

The structure and property of the synthesized products were characterized by means of FTIR, XRD, SEM.

合成产品的结构和形貌分别通过红外光谱、X射线衍射和扫描电子显微镜进行测试表征。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。