电压放大

The amplifiers chosen must be compensated for unity-gain operation and R6 and R7 must be chosen to minimize output errors due to input offset current.

注释 2：(NE5532 注) R4U i =0 R3 首先，对节点处的电流讨论是没有意义的，流入节点的电流一定等于流出节点的电流，再者，I3 与 I4 不是等大反相的关系，分析如下： 40 An Applications Guide for OP Amps 由于此时 OPA1 处于反相放大状态，其输出电压 U o1 压误差按照设计思路，此时 A2 的输出应该等于 U o1 ，则电流方向如上图。

One is auto-zero and the other is chopping. The chopping amplifier with its many parts of modulation switches, pre-amplifier, band-pass selective amplifier, and voltage follower and demodulation switches is designed. The circuit is simulated with HSPICE to optimize. The residual offset of microvolt and the equivalent input noise PSD of 70 nV /Hz were obtained.

zero和斩波Chopping 对失调和噪声的影响，具体针对传感器的信号要求进行了斩波放大电路的调制，预放，带通选择放大器，电压跟随和解调等各个部分的设计，电路使用Hspice进行了仿真优化，达到了微伏量级的残余失调和70 nV /Hz输入等效噪声PSD。

It is shown as a photocell amplifier in the following section.

运算放大器使用指南电流——电压转换电路的用途不限于电流的测量上，还可以用在例如后面的光电池放大电路中。

The AC power supply unit provides AC voltage for the signal generating unit and the high voltage amplifying unit.

直流电源单元为信号发生单元和高压放大单元提供直流电压。

As the design requirements of the voltage is not great, it can be enlarged and help drive push-pull switch transistor.

由于设计要求的电压不是很大，故可采用推挽放大又有利于驱动开关晶体管。

A high-precision signal amplifier system based on DSP is presented for applying in the secondary side of voltage transformer.

提出了应用于电压互感器二次侧的基于数字信号处理器的高精度信号放大系统。

The intelligence motor soft starters partial hardware electric circuit has designed mainly includes the electric current, the voltage examination module, the crystal thyratron triggers and the pulse width enlargement electric circuit module, the numeral keyboard entry and the liquid crystal display output module.

设计了智能型电机软起动器的部分硬件电路，主要包括有电流、电压检测模块、晶闸管的触发及脉宽放大电路模块、数字键盘输入及液晶显示输出模块。

This dissertation researched and developed a DC voltage amplification driver for the IDM.

本文主要研究开发了适用于驱动IDM的电压型直流放大式驱动电源。

About the volume, we can still improve it by modifying the circuit, such as the impedance, the voltage, and the amplification factor.

而最后的音量问题，仍可藉由线路上的修改，如电阻的大小，电压大小，放大倍率。。。来解决

Mainly by the design of infrared sensors, signal amplification circuit, voltage comparator, delay circuit and the audio alarm circuit.

本设计主要由红外线传感器，信号放大电路，电压比较器，延时电路和音响报警电路组成。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。