电动的

MCFE and Rocla, the fifth-largest manufacturer of electric warehouse equipment in Europe, have a long history of cooperation.

MCFE和Rocla ，有一个很长的合作历史在欧洲是第五大生产的电动仓库设备。

According to the study result and with the function requirement of steering system, and by using automobile design and fluid drive theory, the design method of this system and its matching with the whole car are presented.

在此基础上，结合转向系统的功能要求，应用汽车设计和液压传动理论，提出了电动液压助力转向系统及其与整车匹配的设计方法。

Futura Power Plants and Electric Vehicles The Clean Air Act has not produced sufficient improvement in air qulity.

未来的电厂和电动汽车《清洁空气法案》并未给空气质量带来显著的改善。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

Venture Enterprise AUTO EV JAPAN, which is engaged in the development and sales of electric vehicles announced, they are selling two-seater car "Girasole" produced by Start Lab Co.

从事电动汽车开发及销售的风险企业AUTO EV JAPAN宣布，该公司正销售意大利Start Lab公司制造的双座电汽车"Girasole"。

But does the Inizio have the right glamor appeal that is so necessary for selling an electric supercar?

但是否Inizio有权提出上诉的魅力是如此必要出售的电动跑车？

And, at age fifty, he learned to fly. He flies a motor glider and small airplanes.

另外，他在五十岁的时候，学习了电动滑翔机和飞机的飞行技术。

Compact, motorized tool conveniently stored in its own pouch and stores neatly in your golf bag.

高尔夫清洁刷是紧凑型的电动工具，能方便储存在你的高尔夫球袋。

It is found that montmorillonite and kaoline show different behaviors of dissolution and precipitation, which greatly alter the potential grade crossing the whole soil areas.

本文采用自制的电动修复装置，研究了模拟土壤组分高岭土和蒙脱石在外加电场条件下发生的变化。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。