用手

After that man has answered a god to come, pat marital shoulder with the hand, of deep feeling say: Good person, you are a good person really!!!!!

那男人回过神来后，用手拍了拍丈夫的肩，感慨的说：&好人啊，你真是一个好人啊！！！&

His right hand is caressing my back, thought that I before his side incidence, my mother saw me according to not to make an effort slightly with the hand to pat me as convenient, I lost the strength to make a sound his body to lean.

他的右手抚著我后背，想我稍微向他的方向倾前，我母亲见我不依从便用力用手拍了我一下，我失力响他身体倾去。

About two o'clock, you would see him munching a French roll or a penny loaf; not taking it boldly out of his pocket at once, like a man who knew he was only making a lunch; but breaking off little bits in his pocket, and eating them by stealth.

大概两点钟的时候，你就能看见他在咀嚼一个法式面包或者一个小短棍面包。而且总是不像一般踏踏实实吃午饭的人那样，大大方方地拿出来吃。而是用手在口袋里掐下一小块，然后偷偷地吃下去。

Packages may be opened and resealed without affecting the corrosion protection.

防锈纸可以打开查看而不影响其防锈效果（查看时不可以用手直接接触产品

He could estimate the measure of a tree very well by his eye; he could estimate the weight of a calf or a pig, like a dealer.

从一个装一蒲式耳或更多散乱铅笔的盒子里，他能飞快用手抓，而且每抓一次都是一打。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

Or the rough shaggy bark of a pine. In spring I touch the branches of trees hopefully in search of a

我感到树叶的对称美，用手摸着白桦树光滑的树皮或是松树那粗糙的厚厚的树皮。

I pass my hands lovingly about the smooth skin of a silver birch, or the rough shaggy bark of a pine.

我感受到了树叶的对称美，我用手摸着光滑的白桦树树皮或是那粗糙的厚厚的松树树皮。

Test tasks: to check whether the loose connector; hand plate coupling the rotor to move a few laps to see whether rotation and flexible unit, whether there is uneven sound and light and heavy feeling, to determine whether pump or foreign body axis is curved seals, such as the installation is correct; inspection seal on the 20th cavity clean lubricants are added 1 / 2 cavity space; pump unit surface is clean; unit no-load test shift.

试车工作：检查连接件是否松动；用手盘动联轴器使转子转数圈，看机组转动是否灵活，是否有响声和轻重不匀的感觉，以判断泵内有否异物或轴是否弯曲，密封件安装正不正等；检查密封腔内的清洁20号润滑油是否加注1/2腔内空间；泵机组表面是否干净；机组转向空载测试。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐